径向弹簧蓄能密封结构最大接触应力的有限元分析

详细信息    查看全文 | 推荐本文 |

英文篇名：Finite Element Analysis on Maximum Contact Pressure of Radial Spring Energized Sealing Structure 作者：丁大江 ; 刘照智 ; 王飞 ; 杨俊恒 ; 古丽娜 英文作者：DING Dajiang;LIU Zhaozhi;WANG Fei;YANG Junheng;GU Lina;Beijing Institute of Space Launch Technology; 关键词：弹簧蓄能密封结构 ; 最大接触应力 ; 密封特性 英文关键词：spring energized sealing structure;;maximum contact pressure;;sealing characteristics 中文刊名：RHMF 英文刊名：Lubrication Engineering 机构：北京航天发射技术研究所; 出版日期：2019-05-15 出版单位：润滑与密封 年：2019 期：v.44;No.333 语种：中文; 页：RHMF201905029 页数：7 CN：05 ISSN：44-1260/TH 分类号：149-155

摘要

为研究径向弹簧蓄能密封结构的密封特性,针对典型径向弹簧蓄能密封结构,分析其密封机制以及O形弯曲金属螺旋弹簧的弹性特性;采用ANSYS有限元分析软件,建立典型弹簧蓄能密封结构的非线性有限元分析模型,对弹簧蓄能密封圈在不同压缩率、不同介质压力下的接触应力进行分析,研究在多种工况下最大接触应力的变化情况。结果表明:压缩率保持不变时,最大接触应力随着介质压力的增大而增大;介质压力保持不变时,随着压缩率的增大,最大接触应力先增大再减小。对压缩率、介质压力与最大接触应力的关系进行曲线拟合,可用于指导弹簧蓄能密封结构的精确设计。
        Focusing on typical radial spring energized sealing structure,the sealing mechanism and the elastic characteristics of the O shape curved metal spiral spring were analyzed to study the sealing characteristics of radial spring energized sealing structure.A nonlinear finite element model for typical spring energized sealing structure was set up with finite element software ANSYS.Contact pressure of spring energized seal under different compression ratio and different medium pressure was discussed in order to get the change rule under different conditions.The results indicate that the maximum contact pressure is increased with the increasing of medium pressure when the compression ratio is instant.With the increasing of compression ratio,the maximum contact pressure is increased first and then decreased when the medium pressure is instant.The fitting curves between compression ratio,medium pressure and maximum contact pressure were researched,which can be used for accurate design of spring energized sealing structure.

引文

【1】 贾晓红,李坤.弹簧蓄能密封圈轴对称仿真模型建模方法研究[J].润滑与密封,2015,40(11):1-5.JIA X H,LI K.A Research on 2-D axisymmetric finite element model for spring energized seal ring[J].Lubrication Engineering,2015,40(11):1-5.
    【2】 夏廷栋,胥德孝,彭拾义,等.实用密封技术手册[M].哈尔滨:黑龙江科学技术出版社,1985.
    【3】 耿志翔,蔡纪宁,张秋翔.螺旋弹簧PTFE密封圈的性能分析[J].润滑与密封,2005,30(6):56-57.GENG Z X,CAI J N,ZHANG Q X.Performance analysis of helical PTFE spring seals[J].Lubrication Engineering,2005,30(6):56-57.
    【4】 贾晓红,李坤.弹簧蓄能密封圈密封系统的密封特性研究[J].润滑与密封,2015,40(12):116-120.JIA X H,LI K.Research on sealing characteristics of sealing system utilizing spring energized seal ring[J].Lubrication Engineering,2015,40(12):116-120.
    【5】 张英会,刘辉航,王德成.弹簧手册[M].北京:机械工业出版社,1997.
    【6】 王宣银.聚四氟乙烯组合密封圈及其摩擦阻力的计算[J].润滑与密封,1997,22(2):57-59.WANG X Y.Analysis of PTFE composition seal ring and calculation of itsfriction drag[J].Lubrication Engineering,1997,22(2):57-59.
    【7】 倪樵,李国清,钱勤.材料力学[M].武汉:华中科技大学出版社,2010.
    【8】 蔺海荣,冯维明,虞松.材料力学[M].北京:国防工业出版社,2001.
    【9】 尚晓江,邱峰,赵海峰,等.ANSYS结构有限元高级分析方法与范例应用[M].北京:中国水利水电出版社,2008.
    【10】 杨建勇,张赞牢,谌彪,等.有限元分析法在YX形橡胶密封圈设计中的应用[J].后勤工程学院学报,2009,25(3):35-38.YANG J Y,ZHANG Z L,CHEN B,et al.The application of finite element method in the design of rubber sealing YX ring[J].Journal of Logistical Engineering University,2009,25(3):35-38.