短圆柱形钢段对石英砂磨矿效果的影响研究

详细信息    查看全文 | 推荐本文 |

英文篇名：Influence of Short Cylindrical Steel Forging Medium on Grinding Effect of Quartz Sand 作者：何逵 英文作者：HE Kui;College of Vanadium and Titanium,Panzhihua University;Research and Development Center for Efficient Utilization of Secondary Resources from Metallurgical Mineral Processing; 关键词：磨矿 ; 磨矿介质 ; 短圆柱形钢段 ; 石英砂 英文关键词：grinding;;grinding medium;;short cylindrical steel forging;;quartz sand 中文刊名：KYGC 英文刊名：Mining and Metallurgical Engineering 机构：攀枝花学院钒钛学院;冶金矿产二次资源高效利用研发中心; 出版日期：2018-08-15 出版单位：矿冶工程 年：2018 期：v.38;No.182 基金：冶金矿产二次资源高效利用研发中心建设项目;; 四川省发改委项目(川发改投资[2013]991号) 语种：中文; 页：KYGC201804012 页数：4 CN：04 ISSN：43-1104/TD 分类号：56-59

摘要

以石英砂为原料、钢球和短圆柱形钢段为磨矿介质,利用单一因素法分别从磨矿介质配比、磨矿介质充填率、磨矿量、磨矿浓度、磨矿时间等方面展开了磨矿试验,结果表明,短圆柱形钢段磨矿的最佳磨矿条件为:介质配比D30∶D25∶D20=43∶62∶97、介质充填率35%、磨矿量400 g、磨矿浓度60%。当磨矿6 min时,磨矿产品粒度主要以100~150μm为主,磨矿8 min后,石英砂粒度变化甚微,粒径主要集中在38μm,可见短圆柱形钢段对石英砂磨矿具有很好的选择性。
        With quartz sand as raw material,steel balls and short cylindrical steel forgings as grinding media,grinding tests were performed by using a single factor method,in terms of various parameters,such as proportion ratio of grinding media,charge ratio of grinding medium,grinding capacity,pulp concentration and grinding time. Results showed that the optimum grinding conditions for using short cylindrical steel forgings were as follows: the proportion ratio for three forges of D30∶ D25∶ D20 as 43 ∶ 62 ∶ 97,the charge ratio of medium at 35%,the grinding capacity of 400 g per batch,and the pulp concentration of 60%. Particles in the sample after being milled for 6 min were mainly distributed in 100 ~ 150μm. However,after being milled for 8 min,there was no further significant reduction in grain size,and the particle size was mainly concentrated at 38 μm,showing that short cylindrical steel forging medium exhibited excellent selectivity in grinding quartz sand.

引文

[1]刘磊,曹进成,吕良,等.不同破碎方式下磨矿技术效率[J].中国有色金属学报,2015,25(9):2565-2574.
    [2]何逵,库建刚,徐国印,等.钒钛磁铁矿磨矿动力学试验研究[J].矿冶工程,2016,36(6):35-38.
    [3]段希祥.碎矿与磨矿(第2版)[M].北京:冶金工业出版社,2006.
    [4]张宏福.中国钒钛磁铁矿选矿[M].北京:冶金工业出版社,1996.
    [5]李若兰,庞建涛,王灿霞,等.短圆柱型磨矿介质在胶磷矿磨矿工艺中的应用[J].有色金属(选矿部分),2015(1):80-82.
    [6]曾桂忠.磨矿介质尺寸与形状对镍矿石磨矿及选别的影响研究[D].昆明:昆明理工大学国土资源工程学院,2003.
    [7]邓禾淼,肖庆飞,李博,等.铸铁段作为磨矿介质在冬瓜山铜矿的试验研究[J].矿冶,2015,24(5):5-8.
    [8]孙昕,张贵忠,贾光明,等.基于米氏散射理论的激光粒度仪的介绍[J].现代科学仪器,2004(5):40-42.
    [9]马少健,陈建新.球磨机适宜磨矿介质配比的研究[J].金属矿山,2000(11):27-31.