氧化膜对6082铝合金搅拌摩擦焊接头疲劳性能的影响

详细信息    查看全文 | 推荐本文 |

英文篇名：Influence of Oxide Film on Fatigue Property of Friction Stir Welded 6082 Al Alloy 作者：张欣盟 ; 何广忠 ; 王贝贝 ; 杨超 ; 薛鹏 ; 倪丁瑞 ; 马宗义 英文作者：ZHANG Xinmeng;HE Guangzhong;WANG Beibei;YANG Chao;XUE Peng;NI Dingrui;MA Zongyi;CRRC Changchun Railway Vehicles Co., Ltd.;Shenyang National Laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Sciences;School of Materials Science and Engineering, Northeast University; 关键词：金属材料 ; 铝合金 ; 搅拌摩擦焊接 ; 氧化膜 ; 疲劳性能 英文关键词：metallic materials;;Al alloys;;friction stir welding;;oxide film;;fatigue property 中文刊名：CYJB 英文刊名：Chinese Journal of Materials Research 机构：中车长春轨道客车股份有限公司;中国科学院金属研究所沈阳材料科学国家研究中心;东北大学材料科学与工程学院; 出版日期：2019-04-25 出版单位：材料研究学报 年：2019 期：v.33 基金：国家自然科学基金(51331008)~~ 语种：中文; 页：CYJB201904008 页数：7 CN：04 ISSN：21-1328/TG 分类号：61-67

摘要

对6 mm厚的6082-T6铝合金进行两种表面处理然后实施搅拌摩擦焊接,研究了对接面氧化膜对接头组织和疲劳性能的影响。结果表明,进行速度为1000 mm/min的高速焊接时,对接面未打磨和打磨的接头焊接质量都良好,接头强度系数达到81%;两种接头的疲劳性能基本相同,疲劳强度均为100 MPa;少数样品在焊核区外断裂,大部分样品在热影响区断裂。与接头相比,两种接头焊核区的疲劳性能有所提高,均为110 MPa,在疲劳测试中裂纹并未沿"S"线萌生和扩展。
        The polished and as received 6082-T6 Al sheets of 6 mm in thickness were subjected to friction stir welding(FSW) aiming to revealthe effect of surface oxide film on the microstructure and fatigue property of the FSW joint. The results show that high quality FSW joints with a high joint strength coefficient of 81% could be produced by a high welding speed of 1000 mm/min, for the unpolished and polished butt surfaces. Similar fatigue properties were obtained for the two type of FSW joints with the above two surface states, and the fatigue strength was 100 MPa. Most weld joints failed at the heat affected zones, and only a few weld joints failed at the nugget zone(NZ) during fatigue tests. The fatigue strength increased to 110 MPa for the NZ for plates with the above two surface states, and it is revealed during fatigue test that the fatigue cracks did not initiate on and propagate along the so called"S-line".

引文

[1]Mishra R S, Ma Z Y, Friction stir welding and processing[J]. Ma-ter. Sci. Eng., 2005, 50R:1
    [2]Wang K S, Zhang X L, Wang X H, et al. Comparison of fatigue prop-erties between friction stir welds and TIG welds for Al alloy[J].Chin. J. Mater. Res., 2009, 23:1(王快社,张小龙,王训宏等.搅拌摩擦与氩弧焊铝合金接头疲劳性能比较[J].材料研究学报, 2009, 23:1)
    [3]Xue P, Zhang X X, Wu L H, et al. Research progress on friction stir welding and processing[J]. Acta Metall. Sin., 2016, 52:1222(薛鹏,张星星,吴利辉等.搅拌摩擦焊接与加工研究进展[J].金属学报, 2016, 52:1222)
    [4]Zhou C Z, Yang X Q, Luan G H. Effect of oxide array on the fatigue property of friction stir welds[J]. Scripta Mater., 2006, 54:1515
    [5]Jolu T L, Morgeneyer T F, Gourgues-Lorenzon A F. Effect of joint line remnant on fatigue lifetime of friction stir welded Al-Cu-Li al-loy[J]. Sci. Technol. Weld. Joining, 2010, 15:694
    [6]Zeng X H, Xue P, Wang D, et al. Effect of processing parameters on plastic flow and defect formation in friction-stir-welded alumi-num alloy[J]. Metall. Mater. Trans., 2018, 49A:2673
    [7]Sato Y S, Yamashita F, Sugiura Y, et al. FIB-assisted TEM study of an oxide array in the root of a friction stir welded aluminium al-loy[J]. Scripta Mater., 2004, 50:365
    [8]Ren S R, Ma Z Y, Chen L Q. Effect of initial butt surface on ten-sile properties and fracture behavior of friction stir welded Al-ZnMg-Cu alloy[J]. Mater. Sci. Eng., 2008; A479:293
    [9]Liu X Q, Liu H J, Wang T H, et al. Correlation between micro-structures and mechanical properties of high-speed friction stir welded aluminum hollow extrusions subjected to axial forces[J].J. Mater. Sci. Technol., 2018, 34:105
    [10]Wang G Q, Zhao Y H, Hao Y F. Friction stir welding of highstrength aerospace aluminum alloy and application in rocket tank manufacturing[J]. J. Mater. Sci. Technol., 2018, 34:73
    [11]Wang B B, Chen F F, Liu F, et al. Enhanced mechanical properties of friction stir welded 5083Al-H19 joints with additional water cooling[J]. J. Mater. Sci. Technol., 2017, 33:1009
    [12]Wang X J, Wei X L, Zhang L L. Microstructural evolution and mechanical properties of friction stir welded 6082-T6 aluminum alloy[J]. Trans. China Weld. Inst., 2018, 39:1(王希靖,魏学铃,张亮亮等. 6082-T6铝合金搅拌摩擦焊组织演变与力学性能[J].焊接学报, 2018; 39:1)
    [13]Scialpi A,De Filippis L A C,Cavaliere P. Influence of shoulder ge-ometry on microstructure and mechanical properties of friction stir welded 6082 aluminium alloy[J]. Mater. Des., 2007, 28:1124
    [14]Liu F C, Ma Z Y. Influence of tool dimension and welding parame-ters on microstructure and mechanical properties of friction-stirwelded 6061-T651 aluminum alloy[J]. Metall. Mater. Trans.,2008, 39A:2378
    [15]Wang C, Wang B B, Wang D, et al. High-speed friction stir weld-ing of SiCp/Al-Mg-Si composite[J]. Acta Metall. Sin.(Engl.Lett.), 2018, https://doi.org/10.1007/s40195-018-0833-2
    [16]Wang C, Wang B B, Xue P, et al. Fatigue behavior of friction stir welded SiCp/6092Al composite[J]. Acta Metall. Sin., 2018, Doi10.11900/0412.1961.2018.00220(王晨,王贝贝,薛鹏等. SiCp/6092Al复合材料搅拌摩擦焊接头的疲劳行为研究[J].金属学报, 2018; Doi 10.11900/0412.1961.2018.00220)
    [17]Wu C S, Su H, Shi L. Numerical simulation of heat generation,heat transfer and material flow in friction stir welding[J]. Acta Metall. Sin., 2018, 54:265(武传松,宿浩,石磊.搅拌摩擦焊接产热传热过程与材料流动的数值模拟[J].金属学报, 2018, 54:265)
    [18]Wang H L, Zeng X H, Zhang X M, et al. Microstructure and me-chanical property of friction stir weld joints of dissimilar Al-alloys5083 and 6061[J]. Chin. J. Mater. Res., 2018; 32:473(王洪亮,曾祥浩,张欣盟等. 5083和6061铝合金异种搅拌摩擦焊接接头的组织和性能[J].材料研究学报, 2018; 32:473)
    [19]Li Y J, Fu R D, Li Y, et al. Tensile properties and fracture behavior of friction stir welded joints of Fe-32Mn-7Cr-1Mo-0.3N steel at cryogenic temperature[J]. J. Mater. Sci. Technol., 2018; 34:157
    [20]Chen F F, Huang H J, Xue P, et al. Research progress on micro-structure and mechanical properties of friction stir processed ultra-fine-grained materials[J]. Chin. J. Mater. Res., 2018, 32:1(陈菲菲,黄宏军,薛鹏等.搅拌摩擦加工超细晶材料的组织和力学性能研究进展[J].材料研究学报, 2018; 32:1)