形状记忆合金悬臂梁变形特性分析

详细信息    查看全文 | 推荐本文 |

英文篇名：Shape Memory Alloy Cantilever Beam Deformation Characteristics 作者：杨静宁 ; 王其晨 ; 王永祥 英文作者：Yang Jingning;Wang Qichen;Wang Yongxiang;School of Science,Lanzhou University of Technology; 关键词：形状记忆合金 ; 拉压不对称系数 ; 悬臂梁 ; 相变 英文关键词：Shape memory alloy;;Tension-compression asymmetric coefficient;;Semi girder;;Phase transformation 中文刊名：甘肃科学学报 英文刊名：Journal of Gansu Sciences 机构：兰州理工大学理学院; 出版日期：2019-02-25 出版单位：甘肃科学学报 年：2019 期：01 基金：国家自然科学基金项目(11862912) 语种：中文; 页：15-19+30 页数：6 CN：62-1098/N ISSN：1004-0366 分类号：TG139.6

摘要

基于梁的弯曲变形理论,建立了形状记忆合金梁的非线性控制方程,研究了拉压不对称系数对悬臂梁在集中载荷作用下的非线性变形的影响,分析得出相变各阶段梁截面应力分布,自由端的挠度以及相边界变化情况。结果显示,拉压不对称系数越大,中性层位移越大且最大值越靠近固定端;拉压不对称系数对受压侧相边界影响大于受拉侧;随着载荷增加,相边界整体向自由端移动且移动越来越慢。
        The non-linear governing equation of the shape memory alloy beam has been established based on bean bending deformation theory,the effect of non-linear deformation of the tension-compression asymmetric coefficient on cantilever beam under concentrated load effect is researched,and the stress distribution,deflection of the free end and the corresponding boundary changes of the section in each stage are analyzed and gained.The result shows that,the neutral layer distribution has a positive correlation with the tension-compression asymmetric coefficient,and the largest value is closer to the fixed end;The effect of the tension-compression asymmetric coefficient on the phase boundary of the pressure side is larger than that on the tension side;With the increase of the load,the phase boundary moves to the free end,and the speed is more and more slow.

引文

[1]贾志荣,周超,刘琳,等.形状记忆合金及其应用研究进展[J].铸造技术,2017,38(2):257-261.
    [2]薛朋飞,张菲,李岩,等.钛基形状记忆合金研究进展[J].稀有金属,2015,39(1):84-90.
    [3] Aiki T.The Position of the Joint of Shape Memory Alloy and Bias Springs[J].Discrete and Continuous Dynamical System,2017,4(2):239-246.
    [4] Auricchio F,Sacco E.A One-dimensional Model for Super Elastic Shape-memory Alloys with Different Elastic Properties between Austenite and Martensite[J].International Journal of Non-Linear Mechanics,1997.32(6):1101-1114.
    [5] Souza A C,Mamiya E N,Zouain N.Three-dimensional Model for Solids Undergoing Stress-Induced Phase Transformations[J].European Journal of Mechanics-A/Solids,1998,17(5):789-806.
    [6] Ahmadreza E,Mohammad E.Exact Solution for Bending of Shape Memory Alloy Superelastic Beams[Z].Proceedings of the ASME 2011 Conference on Smart Materials,Adaptive Structures and Intelligent System,2011.
    [7]崔世堂,姜锡权,严军.形状记忆合金梁纯弯曲的理论分析[J].应用力学学报,2016,33(1):43-49,179.
    [8]商泽进,王忠民.形状记忆合金梁的非线性弯曲变形[J].机械工程学报,2011,47(18):28-32.
    [9]王吉昌,沈永春,杨静宁.力偶作用下形状记忆合金梁的非线性弯曲理论分析[J].甘肃科学学报,2018,30(2):20-24.
    [10] Auricchio F,Taylor R L,Lubiner J.Shape Memory Alloys:Macromodelling and Numerical Simulateons of the Super Elastic Behavior[J].Computer Methods in Applied Mechanics and Engineering,1997,146(3/4):281-312.
    [11] Liang C.The Constitutive Modeling of Shape Memoryalloys[D].Virginia:Department of Mechanical Engineering.Virginia Polytechnic Institute and State University,1990.