涡旋压缩机动力特性及仿真模拟研究
|
摘要
涡旋压缩机作为一种新型、节能、高效、低噪、省材的容积式流体机械,与其它类型压缩机相比较具有不可替代的优越性,已广泛应用于空调制冷、动力工程等领域。目前逐渐向大气量、大功率的方向发展,应用领域也随之扩大。随着石油化工的发展,压力能的应用日趋广泛,使得涡旋压缩机在国民经济的各个部门成为必不可少的关键设备之一。随着计算机技术的发展和加工制造技术的提高,涡旋压缩机的应用领域得到更为广阔的发展。由于涡旋压缩机特殊的工作原理及结构特点,其潜在的优势并没有完全被挖掘出来。因此,研制与开发高性能的涡旋压缩机具有重大的现实意义。本文依托国家自然科学基金项目“无油润滑涡旋式压缩机的摩擦学与动力学耦合问题研究”和“变容量涡旋压缩机润滑摩擦特性与转子动力学行为研究”,以涡旋压缩机为研究对象,基于圆渐开线理论,建立了涡旋压缩机压缩腔几何模型,泄漏模型、传热模型、动力学模型；借助三维实体建模软件,得到了涡旋压缩机虚拟样机模型；通过转子系统模态、曲轴转子壳体耦合动力学、转子系平衡特性及考虑运动副间隙的机构动力学特性分析,为涡旋压缩机的可靠性设计及高性能研制提供了理论基础。
首先完成涡旋压缩机的虚拟建模和运动仿真,包括建立其部件的三维实体模型、对其零部件进行虚拟装配、样机和部件的运动仿真。建立其零部件三维实体模型,根据涡旋压缩机物理样机的结构特点,描述主要零部件之间相互的位置关系和运动关系,从而确定各零部件在虚拟环境中的相对空间位置,进行虚拟样机的装配工作。校核涡旋压缩机设计是否合理、可靠、主要零部件的动作是否协调和运动过程是否存在干涉。
在涡旋压缩机虚拟建模的基础上,研究涡旋压缩机转子系统动力特性,根据模态分析理论和转子单元运动方程,分析了主轴系各节点的位移和倾角；基于转子动力学理论,得出了主轴轴承的动力特性系数,建立了主轴轴承为刚性支承系统和弹簧—阻尼系统两种分析模型。应用有限元软件对涡旋压缩机两种分析模型的主轴转子系统进行预应力条件下的模态分析,分别获得了两种支承系统条件下的振型,并分析了弹簧—阻尼系统中轴承刚度对其转子动力特性的影响。
利用有限元方法和多体动力学理论,对涡旋压缩机转子和壳体进行有限元模态分析,获得了涡旋压缩机转子和壳体的固有频率和振型等模态特性参数。在涡旋压缩机主轴系拓扑模型的基础上,分别建立了主轴系的多刚体模型和多柔体模型。通过对曲轴系多体动力学仿真分析,得到了气体力载荷和在柔性体条件下壳体承受主副轴承载荷等,分析了壳体在载荷作用下的动力学响应问题。
根据曲柄销所受的切向力大小约为径向力四倍,通过采取平衡曲柄销所受切向力大小平均值及极小值的方法,分别分析了曲柄销切向力不平衡残余量以及曲柄销切向力最小值部分对主轴轴承的影响；对涡旋压缩机轴系和壳体进行受力分析,建立轴系和壳体的力和力矩平衡方程,将壳体的受力和主轴轴承载荷作为设计变量,来分析壳体在受力最佳的情况下,平衡重的安装角度对主轴轴承载荷的影响。
在涡旋压缩机工作过程中,如果计入尺寸误差、运动副间隙和磨损间隙的存在,那么,涡旋压缩机不能完全满足平行四连杆的条件。因此,以涡旋压缩机虚拟样机为对象,建立考虑运动副间隙的转子系统多体动力学模型,并将含间隙运动副的间隙矢量模型、间隙接触碰撞力模型和摩擦力模型嵌入ADAMS软件进行多体动力学仿真。仿真结果可以准确地预测运动副间隙对涡旋压缩机动态特性的影响,为涡旋压缩机设计提供了参考和依据。
通过样机动平衡试验和性能试验,验证了涡旋压缩机的优良性能及可靠性,动平衡试验必要性,为高性能涡旋压缩机的研制与开发奠定了坚实的基础。
As a new high efficiency, low noise, positive displacement compressor, the scroll compressor has an irreplaceable advantage compared with other types of compressors and are widely used in refrigeration, air conditioning, power engineering and other fields. The area of application also been expanded by the development in the direction of the volume of the atmosphere and high power currently. With the development of science and technology, especially the development of petrochemical industry in recent years, scroll compressors in various sectors of the national economy become one of key equipments as the pressure is applied more broadly. With the improvement of computer development and manufacturing, more broad application area of scroll compressor development. Because of the structural characteristics of scroll compressor, its potential advantages have not been fully excavated. Therefore, investigation of scroll compressor with high quality is of great importance in practice. Funded by NSCF funding of "Study of coupling friction and dynamics in oil-free twin-wrap compressor" and "Investigation of friction and rotor dynamics performance in variable volume scroll compressor", the present work is aimed at developing geometrical model, leakage model and heat transfer and dynamic model based on the circle involute theory. Scroll compressor virtual prototype model has been obtained by using the three dimensional entity built die software. By analyzing the subsystem die state, crankshaft shell coupling dynamics of rotor, rotor balance characteristics and dynamic characteristics analysis considering kinematic pair clearance mechanism, a theoretical basis has been developed for reliability design and high performance of scroll compressor.
First, the motion simulation for virtual prototype of scroll compressor was finished, including its solid models of parts, parts of the virtual Assembly and motion simulation of the machine and parts. By Building the solid models of parts, the positional relationship between the various parts have been described with considering the structural characteristics of scroll compressor under the physical prototype, then the relative spatial locations of the parts in a virtual environment has been determined, and virtual prototyping can be assembled. Check for the reasonable, reliable, relevant parts of movement coordination and whether there is interference in the campaign process of the scroll compressor design.
Based on the scroll compressor virtual modeling, the dynamic characteristics of the scroll compressor rotor system were studied, the displacement and tilt of each node spindle system were analyzed according to the equations of motion units and rotor modal analysis theory; the dynamic coefficients of spindle bearings were obtained based on the rotor kinetic theory, and spindle bearings at two analytical models, a rigid support system and spring- damping system,were been established. The two scroll compressor rotor shaft models were analyzed under two conditions support system by using the finite element software, and obtained two vibration modes, the bearing stiffness impacted on its rotor dynamic characteristics also were analyzed at the spring-damper system.
Using the finite element method and multi-body dynamics theory, the scroll compressor rotor and the shell modal were analyzed to obtain the natural frequency of the scroll compressor rotor and the frame and modes such as modal parameters. Based on multi-body models, the scroll compressor shaft topology configuration and flexible multi-body model of the spindle system were established. By analyzing the crankshaft system multi-body dynamics, the gas load and bearing loads under flexible body were obtained, and the dynamics of the frame in response to the problem under load were also analyzed.
According to cut suffered crank pin radial force is about four times the size of the force,suffered through a balanced crank pin size of the average tangential force method to analyze the impact of the crank pin tangential force imbalance residual amount of spindle bearings; By analyzing the scroll compressor shaft and the shell, the force shaft housing and the torque balance equation were established, as design variables, the stress and load bearing spindle housing were used to analyze the impact of the counterweight mounting angle of the spindle bearing loads in the case that force under optimal conditions, to arrive at a balance of high quality and the phase angle and other parameters.
Considering dimensional errors, clearance between turning pairs and wear gap exists, the scroll compressor cannot fully meet the ideal conditions for parallel four-bar, based on the virtual prototyping of scroll compressors, the rotor system of multi-body dynamics model and vector model of pairs with clearances with considering kinematic pair clearance were built, and the clearance model of contact-impact force and friction force model were embedded in ADAMS to carry out dynamics simulation. Simulation results can accurately predict the clearance between turning pairs on dynamic characteristics of scroll compressor, which provide reference and basis for the design of scroll compressors.
By dynamic balance test and prototype performance test, verify the good performance and reliability of scroll compressor, the feasibility and necessity of dynamic balance test for high performance of scroll compressor of the research and development has laid a solid foundation.
首先完成涡旋压缩机的虚拟建模和运动仿真,包括建立其部件的三维实体模型、对其零部件进行虚拟装配、样机和部件的运动仿真。建立其零部件三维实体模型,根据涡旋压缩机物理样机的结构特点,描述主要零部件之间相互的位置关系和运动关系,从而确定各零部件在虚拟环境中的相对空间位置,进行虚拟样机的装配工作。校核涡旋压缩机设计是否合理、可靠、主要零部件的动作是否协调和运动过程是否存在干涉。
在涡旋压缩机虚拟建模的基础上,研究涡旋压缩机转子系统动力特性,根据模态分析理论和转子单元运动方程,分析了主轴系各节点的位移和倾角；基于转子动力学理论,得出了主轴轴承的动力特性系数,建立了主轴轴承为刚性支承系统和弹簧—阻尼系统两种分析模型。应用有限元软件对涡旋压缩机两种分析模型的主轴转子系统进行预应力条件下的模态分析,分别获得了两种支承系统条件下的振型,并分析了弹簧—阻尼系统中轴承刚度对其转子动力特性的影响。
利用有限元方法和多体动力学理论,对涡旋压缩机转子和壳体进行有限元模态分析,获得了涡旋压缩机转子和壳体的固有频率和振型等模态特性参数。在涡旋压缩机主轴系拓扑模型的基础上,分别建立了主轴系的多刚体模型和多柔体模型。通过对曲轴系多体动力学仿真分析,得到了气体力载荷和在柔性体条件下壳体承受主副轴承载荷等,分析了壳体在载荷作用下的动力学响应问题。
根据曲柄销所受的切向力大小约为径向力四倍,通过采取平衡曲柄销所受切向力大小平均值及极小值的方法,分别分析了曲柄销切向力不平衡残余量以及曲柄销切向力最小值部分对主轴轴承的影响；对涡旋压缩机轴系和壳体进行受力分析,建立轴系和壳体的力和力矩平衡方程,将壳体的受力和主轴轴承载荷作为设计变量,来分析壳体在受力最佳的情况下,平衡重的安装角度对主轴轴承载荷的影响。
在涡旋压缩机工作过程中,如果计入尺寸误差、运动副间隙和磨损间隙的存在,那么,涡旋压缩机不能完全满足平行四连杆的条件。因此,以涡旋压缩机虚拟样机为对象,建立考虑运动副间隙的转子系统多体动力学模型,并将含间隙运动副的间隙矢量模型、间隙接触碰撞力模型和摩擦力模型嵌入ADAMS软件进行多体动力学仿真。仿真结果可以准确地预测运动副间隙对涡旋压缩机动态特性的影响,为涡旋压缩机设计提供了参考和依据。
通过样机动平衡试验和性能试验,验证了涡旋压缩机的优良性能及可靠性,动平衡试验必要性,为高性能涡旋压缩机的研制与开发奠定了坚实的基础。
As a new high efficiency, low noise, positive displacement compressor, the scroll compressor has an irreplaceable advantage compared with other types of compressors and are widely used in refrigeration, air conditioning, power engineering and other fields. The area of application also been expanded by the development in the direction of the volume of the atmosphere and high power currently. With the development of science and technology, especially the development of petrochemical industry in recent years, scroll compressors in various sectors of the national economy become one of key equipments as the pressure is applied more broadly. With the improvement of computer development and manufacturing, more broad application area of scroll compressor development. Because of the structural characteristics of scroll compressor, its potential advantages have not been fully excavated. Therefore, investigation of scroll compressor with high quality is of great importance in practice. Funded by NSCF funding of "Study of coupling friction and dynamics in oil-free twin-wrap compressor" and "Investigation of friction and rotor dynamics performance in variable volume scroll compressor", the present work is aimed at developing geometrical model, leakage model and heat transfer and dynamic model based on the circle involute theory. Scroll compressor virtual prototype model has been obtained by using the three dimensional entity built die software. By analyzing the subsystem die state, crankshaft shell coupling dynamics of rotor, rotor balance characteristics and dynamic characteristics analysis considering kinematic pair clearance mechanism, a theoretical basis has been developed for reliability design and high performance of scroll compressor.
First, the motion simulation for virtual prototype of scroll compressor was finished, including its solid models of parts, parts of the virtual Assembly and motion simulation of the machine and parts. By Building the solid models of parts, the positional relationship between the various parts have been described with considering the structural characteristics of scroll compressor under the physical prototype, then the relative spatial locations of the parts in a virtual environment has been determined, and virtual prototyping can be assembled. Check for the reasonable, reliable, relevant parts of movement coordination and whether there is interference in the campaign process of the scroll compressor design.
Based on the scroll compressor virtual modeling, the dynamic characteristics of the scroll compressor rotor system were studied, the displacement and tilt of each node spindle system were analyzed according to the equations of motion units and rotor modal analysis theory; the dynamic coefficients of spindle bearings were obtained based on the rotor kinetic theory, and spindle bearings at two analytical models, a rigid support system and spring- damping system,were been established. The two scroll compressor rotor shaft models were analyzed under two conditions support system by using the finite element software, and obtained two vibration modes, the bearing stiffness impacted on its rotor dynamic characteristics also were analyzed at the spring-damper system.
Using the finite element method and multi-body dynamics theory, the scroll compressor rotor and the shell modal were analyzed to obtain the natural frequency of the scroll compressor rotor and the frame and modes such as modal parameters. Based on multi-body models, the scroll compressor shaft topology configuration and flexible multi-body model of the spindle system were established. By analyzing the crankshaft system multi-body dynamics, the gas load and bearing loads under flexible body were obtained, and the dynamics of the frame in response to the problem under load were also analyzed.
According to cut suffered crank pin radial force is about four times the size of the force,suffered through a balanced crank pin size of the average tangential force method to analyze the impact of the crank pin tangential force imbalance residual amount of spindle bearings; By analyzing the scroll compressor shaft and the shell, the force shaft housing and the torque balance equation were established, as design variables, the stress and load bearing spindle housing were used to analyze the impact of the counterweight mounting angle of the spindle bearing loads in the case that force under optimal conditions, to arrive at a balance of high quality and the phase angle and other parameters.
Considering dimensional errors, clearance between turning pairs and wear gap exists, the scroll compressor cannot fully meet the ideal conditions for parallel four-bar, based on the virtual prototyping of scroll compressors, the rotor system of multi-body dynamics model and vector model of pairs with clearances with considering kinematic pair clearance were built, and the clearance model of contact-impact force and friction force model were embedded in ADAMS to carry out dynamics simulation. Simulation results can accurately predict the clearance between turning pairs on dynamic characteristics of scroll compressor, which provide reference and basis for the design of scroll compressors.
By dynamic balance test and prototype performance test, verify the good performance and reliability of scroll compressor, the feasibility and necessity of dynamic balance test for high performance of scroll compressor of the research and development has laid a solid foundation.
引文
[1]K.TOJO, et al.A Scroll Compressor for Air Conditioners[C].In:Proceedings of International Compressor Engineering Conference at Purdue(ICECP), Pudue, USA,1984,496-503
[2]Creux. Rotary Engineer[P]. U.S. Patent,801,182,1905
[3]L.Nordi. Improvements in or Relating to Fluid Pumps and the Like[P].U.K. Patent Specification,220,296. January 8,1925
[4]R.W.Moore,et al.A Scroll Compressor for shipboard Helium Liquefier System[C].In: ICECP, Pudue, USA,1976,417-422
[5][日]荒井信胜,等.涡旋压缩机及其在箱形空调器上的应用[J].压缩机技术,1985,1：55-59
[6]姜尔宁编译.世界制冷压缩机发展趋势(一)[J].制冷技术,2009,2：46-53
[7][美]David Simpsvn.制冷压缩机的发展与动向[J].制冷技术,1995,1：39-43
[8]夏克盛,等编译.世界压缩机发展趋势[J].制冷技术,2001,1：48-53
[9]李红旗编译.世界各国近期压缩机发展概况(二)[J].家用电器科技,2001,6：66-69
[10]http://www.chinairn.com/news/20120720/435528.html.
[11]杨.GMCC涡旋压缩机下线[J].电器,2011,1：63
[12]王焕然,王迪生.喷油涡旋空压机性能试验研究[J].压缩机技术,1992,2：1-4
[13]樊灵,靳春梅,孙国基,等.大排气量涡旋空压机设计的关键技术[J].压缩机技术,2002,1：5-7
[14]江波,王迪生.微型涡旋式空气压缩机背压机构研究[J].流体机械,1996,24(8)：18-22
[15]赵远扬,李连生,束鹏程.喷水涡旋空气压缩机工作特性的研究[J].西安交通大学学报,2004,38(9)：887-890
[16]房师毅,李连生,束鹏程.无油润滑涡旋式空气压缩机的工作过程研究[J].中国机械工程,2005,16(2)：123-127
[17]汪军,唐甜甜,李连生,等.喷水涡旋空气压缩机压缩过程的换热特性分析[J].流体机械,2003,31(11)：7-9
[18]李超,赵荣珍,刘振全,等.涡旋式空气压缩机润滑系统的研究[J].润滑与密封,2004,164(7)：104-105
[19]司玉宝,屈宗长,王迪生.WXA-1/7型涡旋式空气压缩机的开发[J].流体机械,2000,28(10)：14-17
[20]司玉宝,屈宗长,樊灵,等.新型特种涡旋式空压机的研制[J].压缩机技术,1999,(3)：3-5
[21]高秀峰,王彦峰,郁永章.喷油涡旋空压机喷油孔位置的计算[J].流体机械,1999,27(2)：22-26
[22]马一太,刘圣春,曾宪阳.C02涡旋压缩机泄漏分析[J]压缩机技术,2005,3：36-39
[23]郝璟瑛,王智忠,赵远扬.C02涡旋压缩机动力学特性的研究[J].制冷学报,2011,32(5)：42-46
[24]李超,刘振全,赵荣珍.双端面机械密封在涡旋式天然气压缩机中的应用[J].流体机械,2005,35(7)：49-51
[25]顾兆林,高秀峰,李云,等.新型汽油机用废气涡旋增压器德研究[J].小型内燃机,2000,29(3)：1-7
[26]顾兆林,郁永章,刘传李,等.废气涡旋式增压器的理论研究[J].内燃机工程,1996,17(1)：23-28
[27]李连生,郁永章.外燃式涡旋发动机理论分析与研究[J].西安交通大学学报,1994,28(8)：89-93
[28]顾兆林,郁永章,蒋德明,等.一种废气涡旋增压器[P].中国专利,CN94216734.1
[29]顾兆林,郁永章.新型车用废气涡旋增压器的设计研究[J].车用发动机,1995,(5)：34-37
[30]孟铭,倪计民.车用涡旋增压器型线参数的优化计算[J].同济大学学报,2003,31(3)：343-346
[31]倪计民,孟铭,周奇,等.涡旋增压器与发动机匹配的理论计算研究[J].汽车技术,2002,31(10)：15-18
[32]纪民举,李超,刘振全.车用涡旋增压器与发动机匹配的理论研究[J].压缩机技术,2008,3：14-18
[33]纪民举,李超,刘兴旺,等.涡旋增压器背压密封组件的设计研究[J].压缩机技术,2007,4：20-22
[34]马小礼.车用涡旋增压器设计与性能研究[D].兰州理工大学硕士论文,2007
[35]滑赵杰.车用双侧涡旋增压器的设计研究[D].兰州理工大学硕士论文,2008
[36]江波,王迪生,钱立元.SCP-1.08/0.6涡旋式油泵的研制[J].流体机械,1996,24(2)：15-17
[37]赵宇山.涡旋原理的新应用—涡旋泵[J].压缩机技术,1993,2：2-7
[38]Su, Y., Sawada, T., Takemoto, Haga, S. Theoretical study on the pumping mechanism of a dry scroll vacuum pump. Vacuum Pump 1996,6:815-818
[39]Zhu J., et al. Research on the Discharge Port of Scroll Oil Pump. In:ICECP, Pudue, USA,1992,611-621
[40]T. Kushiro, et al. Development of a Scroll-Type Oil-Free VacuumPump[C].In:ICECP, Pudue, USA,1990,147-155
[41]E.Morishita,etal.Rotating Scroll Vacuum Pump[C].In:ICECP, Pudue, USA,1988,198-205
[42]杨旭,张贤明,王立存,等.UG软件在真空泵涡旋盘建模与仿真中的应用[J].真空,2013,50(2)：10-13
[43]杨广衍,滕普光,张鹏,等.涡旋真空泵的设计与操作[J].真空,2006,43(4)：19-22
[44]王志,巴德纯.涡旋真空泵中固体润滑技术的应用研究[J].沈阳航空工业学院学报,2002,9(2)：20-21
[45]王旭迪,胡焕林.涡旋真空泵型线设计[J].合肥工业大学学报(自然科学版),2001,24(1)：103-105
[46]王旭迪,胡焕林.涡旋式真空泵[J].真空与低温,1999,5(1)：32-34
[47]巴德纯,杨乃恒,李树军,等.涡旋干式真空泵结构对抽气性能的影响[J].真空,1999,(1)：8-11
[48]巴德纯,李树军,许寿华,等.涡旋式无油真空泵动力学研究[J].真空,1998,(4)：12-16
[49]孟冬辉.涡旋无油真空泵设计理论及加工工艺的研究[D].东北大学硕士学位论文,2004
[50]王友亮.涡旋无油真空泵抽气过程的计算机模拟[D].东北大学硕士学位论文,2003
[51]李春燕.无油涡旋真空泵内部流场的计算机模拟与仿真[D].东北大学硕士学位论文,2008
[52]黄英,李建军,韩晶雪,等.干式涡旋真空泵的发展与关键问题[J].真空,2013,50(3)：26-29
[53]邵兵.涡旋泵涡旋齿的压力和温度场模型[J].化工机械,2011,38(5)：588-590
[54]屈宗长,樊灵,阎毓.涡旋输油泵泄漏研究[J].压缩机技术,1998,(6)：3-7
[55]屈宗长,江波,王迪生.新型涡旋输油泵[J].压缩机技术,1998,(2)：33-34
[56]江波,朱杰,畅云峰,等.涡旋式油泵的试验分析[J].压缩机技术,1998,(2)：18-20
[57]屈宗长,阎毓,王迪生.涡旋油泵转速的优化[J].压缩机技术,1997,(5)：30-33
[58]Zhu J., et al. Research on the Discharge Port of Scroll Oil Pump[C]. In:ICECP,Pudue, USA,1992,611-621
[59]张贤明,陈栋,王立存,等.滤油机涡旋真空泵泄漏损耗及密封研究[J].真空,2013,50(4)：26-29
[60]顾兆林,郁永章.新型涡旋式机械原理及其在内燃机中的应用(1)[J].小型内燃机,1995,24(6)：51-56
[61]顾兆林,郁永章.新型涡旋式机械原理及其在内燃机中的应用(2)[J].小型内燃机,1996,25(1)：1-5
[62]顾兆林,郁永章,蒋德明.涡旋式内燃机工作过程的分析研究[J].内燃机工程,1998,19(1)：22-27
[63]顾兆林,郁永章,蒋德明.一种新型内燃机—涡旋式发动机的理论研究[J].西安交通大学学报,1995,29(11)：89-95
[64]陈波,沈永年.两相涡旋膨胀机的性能及实验研究[J].深冷技术,2004,(2)：10-12
[65]王向红,沈永年,王洪明.涡旋式膨胀机泄漏损失的数值计算与分析[J].流体机械,2002,30(9)：18-20
[66]刘井龙,熊联友,侯予,等.一种新型膨胀机—涡旋式膨胀机[J].深冷技术,2000,(4)：13-15
[67]沈永年.涡旋式膨胀机热力过程分析与实验研究[J].低温工程,2000,(4)：23-28
[68]陈波.涡旋式膨胀机的热力特性研究[D].浙江大学硕士学位论文.2004
[69]吴锡江.基于涡旋膨胀机的车用小型余热回收系统开发[D].浙江大学硕士学位论文.2011
[70]严雨林.有机朗肯循环系统涡旋膨胀机工作过程分析与实验研究[D].天津大学,2011
[71]褚晓广,张承慧,李珂,等.涡旋膨胀机发电系统效率优化控制策略[J].电工技术学报,2012,27(6)：25-31
[72]杨兴华,潘家祯,王吉岱,等.涡旋式膨胀机内部流场的数值模拟研究[J].流体机械,2013,41(2)：15-18
[73]屈宗长,朱杰,李心伟,等.多级涡旋压缩机压力比与喷油量的优化[J].西安交通大学学报.1995,29(11)：44-48
[74]Chong, Y.F., et al.A Two Stage Double Acting Scroll Air Compressor. In:ICECP. Pudue, USA,1994:659-663
[75]徐虹玲.并联涡旋式压缩机油平衡特性的试验研究[J].制冷与空调,2013,13(5)：55-57
[76]吴伟军,钟建法,彭仟能.并联涡旋式压缩机在空气源热泵机组中的应用分析[J].制冷与空调,2013,13(1)：55-58
[77]顾兆林,郁永章,蒋德明.双涡圈及多涡圈涡旋机械几何特性的理论研究[J].西安交通大学学报,1998,32(12)：90-93
[78]顾兆林.双涡圈涡旋压缩机理论及应用研究[D].西安交通大学博士论文,1997
[79]刘卫华,高秀峰,冯诗愚,等.双涡圈涡旋机械修正齿形的基元面积计算[J].西安交通大学学报,2002,36(11)：1195-1198
[80]王君,赵嫚,刘兴旺,等.多涡旋齿涡旋压缩机的可用啮合型线研究[J].压缩机技术,2005,6：7-10
[81]王君.多涡旋齿涡旋压缩机啮合型线理论研究[D].兰州理工大学博士论文,2006
[82]Takashi B. etal.Fuel Cell System Having Scroll Type Compressor and Regenerator.Patent:US6361890,2002
[83]Takashi B., et al.Fuel Cell System Having Common Scroll Type Compressor and Regenerator.Patent:US6338912,2002
[84]Zhao Yuanyang, et al.Research on oil-free air Scroll Compressor with high speed in 30 KW fuel cell. Applied Thermal Engineering,2003,23:593-603
[85]C. F. Lai,et al. The Development of Oil-less Scroll Compressor Used for Fuel Cells[C]. Proc. of the 4th International Conference on Compressor and Refrigeration at Xi'an,2003,241-249
[86]李海生.无油润滑涡旋压缩机的研究[D].兰州理工大学硕士论文,2005
[87]李超,刘振全,王君.燃料电池用无油润滑涡旋压缩机研究[J].润滑与密封,2008,33(6)：74-76
[88]邱凯,徐博,乔宗亮.空调用涡旋压缩机背压腔变频特性的实验研究[J].压缩机技术,1997,4：3-5
[89]伍光辉.基于数码涡旋压缩机的空调系统的研究[D].华中科技大学博士论文,2004
[90]彭斌,刘振全,张洪生,等.变频涡旋压缩机的研究与应用[J].兰州理工大学学报,2005,31(1)：60-63
[91]樊灵,屈宗长,靳春梅等.汽车空调用涡旋压缩机变容量调节机构的研究[J].流体机械,1999,27(11)：47-49
[92]廖全平,李红旗.涡旋变频压缩机[J].流体机械,2002,30(2)：35-37
[93]王贻任,Arup Majumdar美国谷轮公司压缩机应用技术讲座,第九讲数码涡旋技术[J].制冷技术,2003,1：35-38
[94]魏栋,梁荣光,萨比特.先进的数码涡旋制冷压缩机技术.低温与特气[J].2006,24(4)：6-9
[95]王宝龙,韩林俊,石文星,等.基于制冷剂泄出的涡旋压缩机容量调节技术[J].制冷学报,2010,31(2)：7-10
[96]李庆伟,刘强.下一代数码涡旋压缩机技术[C].2010年国际制冷技术交流会论文集,2010.8.6
[97]陈斌,陈光明,刘利华,等.混合工质变容量调节技术及其应用[J].流体机械,2004,32(12)：64-68
[98]刘兴旺.提高变频涡旋压缩机压缩性能的方法研究[D].兰州理工大学博士论文,2011
[99](日)森下悦生,等.邓立文译.涡旋压缩机的几何理论.流体工程,1985,(10)：38-48
[100](日)森下悦生,杉原正浩.涡旋压缩机的设计问题[J].压缩机技术,1988,4：11-20
[101]M.Hayano.Performance Analysis of Scroll compressor for Air Conditioner[C].In: ICECP, Pudue, USA,1986, (2):836-871
[102]黄允东,郁永章.半圆片偏心线涡旋压缩机的几何理论[J].压缩机技术,1997,1：3-6
[103]K.Tojo, et al. New Wrap profile for Scroll Type Machine[C]. Proceedings of 19th International Congress of Refrigeration, Hague, The Netherlands,1995(3a):515-521
[104]H.Kohsokable, et al. Study on Scroll Profile Based on Algebraic Spiral for Scroll Fluid Machine[J]. Transactions of the JAR,1994(11), No.3:337-347
[105]李连生,郁永章,束鹏程.采用渐开线的涡旋型线理论研究[J].流体机械,1994,22(5)：50-56
[106]李连生.线段渐开线涡旋压缩机的几何理论[J].流体机械,1994,22(12)：22-28
[107]李连生,束鹏程,郁永章,等.涡旋型线对涡旋式压缩机性能的影响[J].西安交通大学学报,1997,31(2)：45-50
[108]Liansheng Li,Pengcheng Shu, Yongzhang Yu. Effect of scroll wraps on performances of scroll compressor[C].In:ICECP. Pudue, USA,1996:579-585
[109]Li,Liansheng, Shu,Pengcheng, Yu,Yongzhang.The effect of scroll wraps on the performance of scroll compressor[J].International Journal of Refrigeration.1997, 20(5):326-331
[110]李连生,束鹏程,黄炯,等.涡旋式压缩机排气系统气流脉动现象研究[J].应用力学学报,1997,14(3)：84-89
[111]李连生,束鹏程.涡旋型线对排气口侵入及排气流速的分析计算[J].西安交通大学学报,2000,32(7)：56-59
[112]王国梁,李连生,张薇,等.一种新型涡旋型线的几何理论研究[J].西安交通大学学报,2003,37(5)：499-503
[113]王国梁.一种新型涡旋压缩机型线的几何理论及其应用研究[D].西安交通大学博士学位论文,2003
[114]王君,刘振全,李超.涡旋压缩机渐开线和圆弧组合型线的设计计算[J].流体机械,2004,32(10)：10-13
[115]王君,查海滨,张晓慧,等.一种渐变啮合间隙的变壁厚涡旋齿型线研究[J].工程热物理学报,2013,34(8)：1453-1456
[116]J.W.Bush,et al.Derivation of general relation governing the conjugate of scroll profile[C].In:ICECP. Pudue, USA, 1992,1079-1088
[117]J.W.Bush,et al.Maximizing Scroll Compressor Displacement Using Generalized Wrap Geometry[C].In:ICECP. Pudue, USA, 1994, 205-210
[118]畅云峰,朱杰,江波,等.涡旋压缩机啮合理论及通用型线控制方程[J].压缩机技术,1998,2：12-13
[119]樊灵,靳春梅,屈宗长,等.通用型线涡旋压缩机的误差及运动分析[J].机械工程学报,2002,38(6)：139-143
[120]樊灵,靳春梅,屈宗长,等.涡旋压缩机型线的误差灵敏度与径向啮合间隙的相关分析[J].机械工程学报,2003,39(4)：151-154
[121]屈宗长,樊灵,王迪生.通用型线涡旋压缩机的几何理论[J].西安交通大学学报.1999,33(11)：39-42
[122]樊灵.涡旋压缩机型线通用数学模型及实验研究[D].西安交通大学博士学位论文,2000
[123]刘涛,邬再新,刘振全.法向等距线法生成涡旋压缩机型线的研究[J].机械工程学报,2004,40(6)：55-58
[124]T.Hirano.Scroll profiles for scroll fluid machines[J].MHI Tech Rev, 1990, 27(1): 35-41
[125]T.Hirano.Scroll - type fluid machine with specific inner curve segments[P].Patent:US 4856973,1989
[126]朱杰.涡旋压缩机径向柔性机构的研究[D].西安交通大学博士学位论文,1994
[127]朱杰,江波,畅云峰,等.涡旋压缩机高压区型线的优化研究[J].压缩机技术,1998,2：7-8
[128]朱杰,畅云峰,江波,等.涡旋压缩机一种优化型线的几何理论[J].压缩机技术,1998,2：43-46
[129]Lee, et al.On the Profile Design of a Scroll Compressor[J].International Journalof Refrigeration,1995,18(5):308-317
[130]刘振全,杜桂荣,於时才.涡旋式压缩机涡旋齿修正的新方法[J].甘肃工业大学学报,1990,16(4)：1-6
[131]刘振全,於时才,杜桂荣.涡旋压缩机涡旋齿修正的图解法和修正角的研究[J].制冷学报,1992,52(2)：6-10
[132]Liu Zhenquan, Du Guirong, Yu shicai, et al.The graphic method of modified wrap of scroll compressor[C].In:ICECP. Pudue, USA,1992:1099-1106
[133]Liu Zhenquan, Du Guirong,Yu Shicai.The mathematical derivation and analysis of the graphic method for wrap modification of the scroll compressor[C].In:Proc. of the 93th International Compressor Technique Conference.Sponsored by Xi'an Jiaotong University,Xi'an, China.1993:482-489
[134]Liu Zhenquan, Du Guirong, Qi Zhiyong, etal.The conjugacy analysis of modified part of scroll profiles. In:ICECP. Pudue, USA,1994:479-484
[135]Wang Baolin, Li Xianting, Shi Wenxing.A General Geometrical Modle of Scroll Compressors Based on Discretional Initial Angles of Involute[J].International Journal of Refrgeration,2005,28:958-966
[136]冯诗愚,顾兆林,李云.涡旋机械的涡旋体始端型线研究[J].西安交通大学学报,1998,32(1)：88-92
[137]高秀峰,冯诗愚,顾兆林,等.涡旋齿端不等β角圆弧类型线修正研究[J].西安交通大学学报,1999,33(12)：56-60
[138]高秀峰,冯诗愚,顾兆林,等.对称圆弧修正齿型涡旋压缩机排气孔的开设分析[J].西安交通大学学报,2000,34(6)：89-92
[139]高秀峰,刘卫华,冯诗愚,等.涡旋齿端等p角圆弧类型线修正理论的研究[J].西安交通大学学报,2001,35(7)：750-754
[140]高秀峰.涡旋压缩机齿形修正及排气孔研究[D].西安交通大学博士学位论文,2000
[141]王君,刘振全.双涡圈涡旋压缩机完全啮合型线修正理论研究[J].机械工程学报,2005,41(3)：234-238
[142]王君,刘振全.涡旋压缩机渐开线类型线的双圆弧修正[J].机械工程学报,2005,41(9)：202-206
[143]王君,刘振全.涡旋压缩机双圆弧修正解析法设计及误差分析[J].上海交通大学学报,2005,39(9)：1418-1421
[144]王君,刘振全.涡旋压缩机渐开线型线的多对圆弧修正[J].北京理工大学学报,2005,25(9)：757-760
[145]王君,刘振全.多涡旋齿涡旋压缩机型线的双圆弧修正研究[J].中国机械工程,2006,17(15)：1553-1556
[146]王伟.涡旋压缩机涡旋新型线及系统动力学研究[D].重庆大学硕士论文,2004
[147]宋立权,陈进,王伟.基于三基圆的涡旋压缩机型线研究[J].中国机械工程,2005,16(16)：1458-1461
[148]Liu tao, Liu zhenquan. Study on Geometry Theory of Trigonometric-curve Modification of Scroll Compressor[C]. In:ICECP. Pudue, USA,2004, CO43
[149]刘振全,杜桂荣.涡旋压缩机理论机构模型[J].机械工程学报,1999,35(2)：38-41
[150]Liu Zhenquan, Tadashi, Yanagisawa.A Mechanical Model For The Scroll Mechanism And Its Kinematical Analysis. In:ICECP. Pudue, USA,1998:507-512
[151]刘振全,柳泽正.涡旋机械的机构模型及理论分析[J].甘肃工业大学学报,1996,22(2)：36-42
[152]杜桂荣,刘振全.涡旋压缩机机构模型及径向随变调节原理[J].制冷学报,1997,2：1-7
[153]周家胜.公转型与回转型涡旋流体机械[J].压缩机技术,1997,5：12-13
[154]周莺.回转型涡旋流体机械[J].压缩机技术,2004,1：30-32
[155]樊灵,靳春梅,屈宗长,等.基于四杆机构的涡旋压缩机的平衡分析[J].机械设计,2000,2：42-44
[156]Barito, Yu Chen.Analysis for Development of the Ant-Rotational Roller Clutch Device for Scroll Compressor[C].In:ICECP. Pudue, USA,1996:451-457
[157]周家胜.涡旋压缩机防自转机构[J].压缩机技术,1995,3：5-10
[158]杜桂荣,刘振全,秦子荣.涡旋式压缩机的防自转机构[J].甘肃工业大学学报1991,17(3)：1-6
[159]Pierre Ginies, Christophe Ancel and Remi Bou Dargham.Three-Crankshaft-Driven Scroll Compressor[C]. In:ICECP. Purdue, USA.2006:C144
[160]刘振全,赵嫚,李超.涡旋压缩机曲柄销防自转机构分析[J].兰州理工大学学报,2006,32(4)：53-55
[161]赵嫚.涡旋压缩机机构动力特性的研究[D].兰州理工大学硕士学位论文,2006
[162]李超,单彩侠,余鹏飞,等.涡旋压缩机小曲拐防自转机构的动力特性[J].兰州理工大学学报,2008,34(1)：50-53
[163]郑尚书.无油润滑涡旋压缩机防自转机构动力特性研究[D].兰州理工大学硕士论文,2013
[164]朱杰.涡旋压缩机径向柔性机构的研究[D].西安交通大学博士学位论文,1994
[165]李吉功.空调用涡旋压缩机的径向柔性机构研究及整机CAD软件开发[D].兰州理工大学硕士论文,1997
[166]翟俊霞.涡旋压缩机随变机构的研究[D].兰州理工大学硕士论文,1998
[167]李超,赵荣珍,刘振全.涡旋压缩机径向随变机构动力学模型研究[J].压缩机技术,2004,3：7-8
[168]刘涛,杜桂荣,邬再新.涡旋压缩机的径向柔性密封机构[J].机械工程师,1999,11：6-7
[169]刘涛,邬再新.一种涡旋压缩机径向随变机构的设计[J].流体机械,2001,29(7)：17-19.
[170]李元鹤.涡旋式压缩机轴向柔性机构的研究[D].西安交通大学博士学位论文,2000
[171]赵兴艳,刘振全.具有双背压腔涡旋压缩机的研制[J].甘肃工业大学学报,1999,25(1)：50-54
[172]屈宗长,王开宁,李元鹤,等.背压平衡涡旋压缩机传热学研究[J].陕西工学院学报,1998,14(1)：38-44
[173]高秀峰,郁永章.涡旋压缩机二次平衡及背压孔研究[J].流体机械,1999,27(7)：15-19
[174]屈宗长,李心伟,李绍平.背压平衡涡旋压缩机的研究[J].西安交通大学学报,1998,32(7)：51-55
[175]Zhu Jie, et al.Research on Self Adjusting Back-pressure Mechanism of Scroll Compressor[C].In:ICECP.Purdue,USA,1992:1137-1145
[176]Zhu Jie, et al. Theoretic Model of Back-pressure Chamber for Scroll Compressor[C]. In:ICECP. Purdue, USA,1992:1127-1135.
[177]Toji, I.Hayase. Self-adjusting Back Pressure Mechanism for Scroll Compressor[C].In: ICECP. Purdue, USA,1988:901-906
[178]唐光德,王文彦,许修铭.涡旋式压缩机轴向柔性补偿机构设计[J].制冷与空调,2006,2(6)：34-37
[179]Nieter J J.Dynamic of compliance mechanisms in scroll compressors part 1:Axial compliance[C].In:ICECP. Purdue, USA, 1990:173-182
[180]J.Niete.Dynamics of Compliance Mechanisms in Scroll Compressors Part 1: Axial Compliance[C].In:ICECP. Purdue, USA, 1992:309-316
[181]T.Shu, et al.Dynamics of Orbiting Scroll with Axial Compliance, Part 1: Simulation of Orbited Axial Motion[C]. In:ICECP. Purdue, USA,1992:861-870
[182]J. Marchese, et al.Dynamics of Orbiting Scroll with Axial Compliance, Part 2: Experimental Techniques[C]. In:ICECP. Purdue, USA, 1992:871-882
[183]W. Bush, et al.General Stability and Design Specification of the Back-pressure Supported Axially Compliant Orbiting Scroll[C].In:ICECP. Purdue, USA, 1992:853-860
[184]Noriaki Ishii, Kenichi Bird, Kiyoshi Sano, et al. Refrigerant leakage flow evaluation for scroll compressors[C]. International Compressor Engineering Conference at Purdue University, West Lafayette, Indiana, USA:1996:633-638
[185]Cko Namkyu, Yang Young, Lee Byung Chul, et al.The characteristics of tangential leakage in scroll compressors for air conditioners[C].In:ICECP. Purdue, USA, 2000, Volume I:807-814
[186]Itoh Takahide et al. Leakage characteristics of scroll compressor by two phase flow model in consideration of wall oil film thickness[J].Transactions of the Japan Society of Mechanical Engineers, Part B, 2002, 68:671
[187]朱杰.涡旋压缩机的泄漏模型及性能计算机程序[J].制冷学报,1992(4)：15-18
[188]江波,畅云峰,朱杰,等.涡旋压缩机内部泄漏的流态分析[J].压缩机技术,1998,(2)：21-23
[189]李力,张占收,边红卿.涡旋压缩机径向间隙的泄漏[J].河北工业科技,1999,16(55)：17-23
[190]屈宗长,孙存慧,司玉宝,等.涡旋压缩机中气体泄漏的估算[J].压缩机技术,1998,(2)：35-37
[191]李超,梁秋立,赵嫚.表面粗糙度对无油润滑涡旋压缩机微间隙泄漏的影响[J].流体机械,2011,39(4)：40-43
[192]李超,赵荣珍,刘振全.涡旋压缩机机构误差对密封间隙的影响[J].润滑与密封,2007,32(7)：66-71
[193]刘兴旺,田玉恒,刘振全,等.涡旋压缩机轴向间隙中流体在层流流态下的泄漏研究[J].流体机械,2004,32(7)：9-11
[194]刘兴旺,赵嫚,李超,等.涡旋压缩机的径向迷宫密封研究[J].机械工程学报,2012,48(21)：97-104
[195]K.Jang, S.Jeong.Experimental investigation on convective heat transfer mechanism in a scroll compressor[J].International Journal of Refrigeration, 2006, 29:744-753
[196]R.J.Rogers, et al.Scroll Compressor Flow Modeling: Experimental and Computational Investigation[C]. In:ICECP. Pudue, USA, 1990:206-215
[197]G.H.Lee.Performance Simulation of Scroll Compressors[J].Proceedings of the Institution of Mechanical Engineers Vol 216 Part A:Journal of Power and Energy. 2002:169-179
[198]E. Morishita, et al. Scroll Compressor Analytical Model[C]. In:ICECP. Pudue, USA, 1984:487-495
[199]Ooi, Kim Tiow, Zhu, Jiang.Convective Heat Transfer in a Scroll Compressor Chamber:a2-D Simulation[J].International Journal of Thermal Sciences.2004,43(7): 677-688
[200]S.Pietrowicz,etal. Mathematical Modeling of Physical Processes in the Scroll Compressor Chamber[J].In:ICECP. Pudue, USA,2002, C20-6
[201]K. T. Ooi,et al. Convective heat transfer in a scroll compressor chambena 2-Dsimulation[J].International Journal of Thermal Sciences,2004,43:677-688
[202]Y. Chen,et al. Mathematical Modeling of Scroll Compressors-Part I:Compression Process Modeling[J].International Journal of Refrigeration,2002,25:731-750
[203]Y. Chen, et al. Mathematical Modeling of Scroll Compressors-Part Ⅱ:Overall Scroll Compressor Modeling[J].International Journal of Refrigeration, 2002, 25: 751-764
[204]冯健美.涡旋式空气压缩机排气孔工作特性研究和排气流动的三维数值模拟计算[D].西安交通大学博士论文,2003
[205]冯健美,屈宗长,李心伟.涡旋压缩机排气过程的三维数值模拟计算[J].西安交通大学学报,2004,38(11)：1141-1146
[206]E.Morishita, et al.Scroll Compressor Analytical Model[C].In:ICECP.Pudue, USA,1984,487-495
[207]N. Ishii, et al.A Study On Dynamic Behavior of A Scroll Compressor[C].In:ICECP. Pudue, USA,1986,901-916
[208]N. Ishii, et al.On The Superior Dynamic Behavior of Variable Rotating Speed Scroll Compressor[C].In:ICECP. Pudue, USA,1988,75-82
[209]林隐虎.涡旋压缩机的力学模型[J].压缩机技术,1991,6：1-8
[210]吴建华,束鹏程.涡旋压缩机的动力分析[J].制冷学报,1995,(4)：1-8
[211]司玉宝,屈宗长,王迪生.涡旋压缩机型线动力特性的研究[J].西安交通大学学报,2000,34(11)：53-56
[212]刘振全,高艳,王君.双头涡旋齿涡旋压缩机气体力分析[J].制冷学报,2005,26(3)：42-46
[213]R.Williams, et al.Scroll Compressor with No Tipping Moment[C].In:ICECP. Pudue, USA,1998:165-173
[214]Liu tao, Liu zhenquan.Investigation of scroll compressor with no overturning moment[C].In:Proc. of the 2003'International Compressor Technique Conference. Sponsored by Xi'an Jiaotong University, Xi'an, China,2003,128-132
[215]Li Chao, Liu zhenquan.The study of characteristics with smaller overturning moment for scroll compressor[C].In:ICECP. Pudue, USA,2004,12-15
[216]樊灵,耿森林,屈宗长,等.涡旋压缩机的平衡分析[J].机械科学与技术,2000,6：935-937
[217]柏杰,李连生,郁永章.涡旋式压缩机动力特性分析[J].西安交通大学学报,1994,28(8)：83-88
[218]J.Kim, et al.Design of Phase-angled Balance Weights for an Inverter Driven Scroll Compressor[C].In:ICECP. Pudue, USA,1998:749-745
[219]刘振全,任俊士.涡旋压缩机的振动时域和频域分析[J].甘肃工业大学学报,2000,26(1)：49-53
[220]刘振全,任俊士.立式涡旋压缩机的振动分析[J].流体机械,2000,28(1)：20-23
[221]周雷,金光喜,谢友柏,等.无油压缩机滑动轴承磨损过程的动态模拟[J].润滑与密封,1996,6：28-30
[222]曹霞,陈芝久,刘振全.立式高压型涡旋压缩机摩擦副分析[J].上海交通大学学报,2000,34(9)：1228-1231
[223]刘兴旺,刘振全,李超等.涡旋压缩机摩擦损耗和泄漏损耗研究[J].压缩机技术,2006,(3)：1-4
[224]焦瑜.基于分形理论的无油润滑涡旋压缩机端面摩擦问题研究[D].兰州理工大学硕士论文,2011
[225]张静.无油润滑涡旋压缩机的摩擦学问题研究[D].兰州理工大学硕士论文,2012
[226]李超,焦瑜,张静,等.动静涡旋端面摩擦副摩擦力分形预测模型[J].化工学报,2012,63(8)：2524-2530
[227]彭斌,孙迎,张力.变截面涡旋压缩机几何模型及摩擦损失模型[J].兰州理工大学学报,2012,38(3)：34-38
[228]T.Drost.Analytical and Experimental Investigation of a Scroll Compressor Lubrication System[C].In:ICECP. Pudue, USA,1992:551-560
[229]Shozo Hase, et al.Development of the High Efficiency Horizontal Type Scroll Compressor[C]. In:ICECP. Pudue, USA,1996:447-452
[230]Sano, et al.A High Reliability Study of Scroll Compressor[C].In:ICECP. Pudue, USA,1996:199-204
[231]赵兴艳,刘振全.涡旋压缩机润滑系统润滑油量优化分析[J].甘肃工业大学学报,1997,23(2)：37-41
[232]Michael M. Cui. Investigation on the Oil Supply System of a Scroll Compressor[C]. ICECP. Pudue, USA,2004, C093
[233]李超,赵荣珍,刘振全,等.涡旋式空气压缩机润滑系统的研究[J].润滑与密封, 2004,164(7)：104-105
[234]王君,李超,马小礼,等.涡旋压缩机工作腔润滑油密封的实验研究[J].润滑与密封,2006,3：100-103
[235]Park, Youn Cheol, Kim,Yongchan, Cho, Honghyun.Thermodynamic Analysis on the Performance of a Variable Speed Scroll Compressor with Refrigerant injection[C]. International Journal of Refrigeration. 2002, 25(8):1072-1082
[236]Dutta, Asit K.,Yanagisawa, Tadashi, Fukuta, Mitsuhiro.An Investigation of the Performance of a Scroll Compressor under Liquid Refrigerant Injection[J]. International Journal of Refrigeration, 2001,24(6):577-587
[237]Cho, Honghyun, Chung, Jin Taek, Kim, Yongchan. Influence of Liquid Refrigerant Injection on the Performance of an Inverter-driven Scroll Compressor[J].International Journal of Refrigeration, 2003, 26(1):87-94
[238]T.Hirano, et al.The Scroll Compressor with variable Capacity Control Mechanism for Automotive Air Conditioner[C].In: ICECP. Pudue, USA,1990:121-130
[239]Kawabe, et al.Development of 2 in 1 Type Scroll Compressor[C].In: ICECP. Pudue, USA,1992:593-601
[240]尚广庆,孙春华.基于UG的涡旋压缩机涡盘设计和制造[J].煤矿机械,2007,28(5)：98-100
[241]乔宗亮,胡志平.涡旋压缩机涡旋盘加工中若干问题探讨[J].压缩机技术,1993,2(118)：14-17
[242]李心伟,江波,冯健美.涡旋压缩机型线加工方法分析(上)[J].数控加工技术,2002,11：29-30
[243]谢利昌.涡旋压缩机大批量生产的几个关键技术问题[J].机械设计与制造,2000,5：32-35
[244]Jiang, Z., Harrison, D.K., Cheng, K. Computer-aided Design and Manufacturing of Scroll Compressors[J]. Journal of Materials Processing Technology. 2003, 1:145-151
[245]王涛,桑伟波,蒋立军.涡旋盘在普通加工中心上的编程加工[J].压缩机技术,2006,(2)：36-37
[246]王平,魏晓伟,安家菊.汽车空调涡旋盘快速硬质阳极氧化处理工艺研究[J].汽车技术,2006,(8)：30-33
[247]王训杰,刘勇,李菊华.UG软件在涡旋压缩机涡旋盘设计与加工中的应用[J].机床与液压,2010,38(8)：35-37
[248]房怀英,杨建红.涡旋压缩机定子加工位置偏差的快速测量[J].华侨大学学报(自然科学版),2010,31(5)：491-495
[249]查谦,查世樑.涡旋压缩机涡旋盘的精加工[J].压缩机技术,2012,(4)：38-40
[250]刘四虎,熊则男,朱均.一种对涡旋体线轮廓度误差进行评价的新方法[J].西安交通大学学报,1996,30(7)：19-24
[251]欧阳林子,陈仰贤,苏建宁,等.一种检测涡旋压缩机涡旋盘的新方法[J].甘肃工业大学学报,2000,30(4)：34-37
[252]李凤宇,欧阳林子,陈仰贤,等.涡旋体加工质量的检测[J].中国机械工程,2002,13(24)：2094-2096
[253]李灿杰.基于振动信号的涡旋压缩机噪声检测系统研究[D].大连理工大学硕士论文,2010
[254]文雅珊.涡旋压缩机主要零部件检测装置设计[D].南昌大学硕士论文,2012
[255]罗伟.涡旋压缩机装配线规划及其部件检测装置设计[D].南昌大学硕士论文,2012
[256]刘强飞.涡旋压缩机定盘面轮廓度检测技术研究[D].南昌大学硕士论文,2012
[257]M. E. Marler, K. B. Kumar. Determination of Scroll Wrap Contact Stress Using the Boundary Element Method[C]. In:ICECP. Pudue, USA, 1992:1117-1125
[258]陈志澜,乔宗亮,熊则男.涡旋压缩机HFC替代工质的研究[J].制冷学报,1995,(1)：1-4
[259]Kohayakawa, et al. Performance Evaluation of Horizontal Type Scroll Compressor for Alternative Refrigerant(R410A) [C]. In: ICECP. Pudue, USA,1998:435-440
[260]刘振全,戚智勇.涡旋压缩机动涡盘应力及变形的研究[J].流体机械,1995,23(10)：23-26
[261]金丹,陈旭,田涛.非均匀温度场下涡旋压缩机动涡盘的盈利及变形分析[J].流体机械,2003,6(31)：11-14
[262]Guir du, Tao Liu,Boxian Qiu, et al.The FEM Analysis of Ahell of Acroll Compressor[C].Proceedings of the 2001'International Compressor Technique Conference.Sponsored by Xi'an Jiaotong University, Xi'anChina,2001:248-253
[263]强建国.涡旋压缩腔几何模型与涡旋齿强度研究[D].兰州理工大学博士论文,2007
[264]王君,张娜,刘凯.基于流场模拟的涡旋压缩机涡齿应力变形分析[J].工程热物理学报,2012,33(8)：1334-1337
[265]Takahide Itoh, Akoto Fujitani, Kimiharu Takeda. Investigation of Discharge Flow Pulsation in Scroll Compressors[C].In: ICECP. Pudue, USA, 1994:683-688
[266]W. Bush, et al.Controlling Discharge Valve Closing Impact in Scroll Machine[C].In: ICECP. Pudue, USA,1998:631-636
[267]王珍,赵之海,杨春立,等.涡旋压缩机振动噪声特性的应用研究[J].压缩机技术,2005,(5)：17-19
[268]屈宗长,李元鹤,王开宁,等.转速对涡旋压缩机性能的影响[J].陕西工学院学报,1997,13(4)：32-37
[269]刘兴旺,姚淑婷,张天龙,等.转速对变频涡旋压缩机压缩性能的影响研究[J].流体机械,2011,39(10)：4-9
[270]邓定国,束鹏程.回转压缩机[M].北京：机械工业出版社,1989
[271]顾兆林,郁永章,冯思愚.涡旋压缩机及其他涡旋机械[M].陕西：陕西科学技术出版社,1998
[272]熊则男,乔宗亮.压缩机设计中的力学分析[M].北京：机械工业出版社,1997
[273]熊则男,乔宗亮.回转压缩机与泵[M].北京：机械工业出版社,1995
[274]N. Ishii,et al.A Study on Danamic Behavior of a Scroll Compressor[C].In:ICECP. Pudue, USA,1986:901-916
[275]H. Iwata,et al. Prediction of Noise from a Scroll Machine[C].In:ICECP.Pudue, USA,1992:977-986
[276]H. Ishii, et al. On the Superior Dynamic Behavior of a Variable Rotating Speed Scroll Machine[C].In:ICECP.Pudue,USA,1988:75-82
[277]李连生.涡旋压缩机[M].北京：机械工业出版社,1995
[278]郁永章.容积式压缩机技术手册[M].北京：机械工业出版社,2000
[279]J.J.Nieter,etal. Counterweighting Scroll Compressor for Minmal Bearing Loads[C].In: ICECP. Pudue, USA,1988:175-181
[280]郭卫东.虚拟样机技术与ADAMS应用实例教程[M].北京：北京航空航天大学出版社,2008.
[281]朱海荣,彭培英,王群辉.基于ADAMS的往复式活塞式压缩机运动机构仿真研究[J].机械设计与制造,2010,32(9)：83-84
[282]白亮亮,唐良宝.基于ADAMS活塞压缩机动平衡虚拟设计[J].流体机械,2008,36(6)：43-45
[283]单彩霞.涡旋压缩机防自转机构动力特性的研究[D].兰州理工大学硕士学位论文,2008,33-34
[284]李超,赵荣珍,刘振全.驱动轴承内嵌式涡旋压缩机特性分析[J].制冷学报,2006, 27(2)：44-47.
[285]孟铭,倪计民.车用涡旋增压器型线参数的优化计算[J].同济大学学报,2003,31(3)：343-346
[286]顾兆林,郁永章,蒋德明.涡旋式内燃机工作过程的分析研究[J].内燃机工程,1998,19(1)：22-27
[287]ZhaoYuanyang et al.Research on oil-free air scroll compressor with high speed in 30 KW fuel cell[J].Applied Thermal Engineering,2003,23:593-603
[288]顾兆林.涡旋压缩机及其它涡旋机械[M].西安：陕西科学技术出版社,1998
[289]刘延柱,陈文良,陈立群.振动力学[M].北京：高等教育出版社,1998
[290]王娅卫,任兴民,秦卫阳,等.转子系统动力特性分析[J].机械科学与技术,2002,21(1)：49-51
[291]Wu JJ, Whittaker A R. Cartmell M P. Dynamic Responses of Structures to Moving Bodies Using Combined Finite Element and Analytical Meth[J]. International Journal of Mechanical Sciences,2001,43(11):2555-2579
[292]王云,雷娜.旋转冲压发动机冲压转子振动模态分析[J].南昌航空大学学报,2008,22(2)：22-25
[293]杜桂荣,刘涛.涡旋式压缩机动涡旋有限元分析方法[J].机械工程学报,1999,35(4)：99-102
[294]郝璟瑛,王智忠,赵远扬,等.C02涡旋压缩机动力学特性的研究[J].制冷学报,2011,32(5)：42-46
[295]胡萍,王珍,赵之海,等.基于模态分析的涡旋压缩机主轴固有特性研究[J].压缩机技术,2007,31(6)：5-7
[296]王君,张娜,刘凯,等.基于流场模拟的涡旋压缩机涡齿应力变形分析[J].工程热物理学报,2012,33(8)：1334-1337
[297]张晓君,张波.涡旋压缩机传动系统动平衡研究与优化[J].机械设计与制造,2012,(4)：149-151
[298]郭仁宁,赵鑫,赵品.涡旋式空气压缩机一次平衡的稳定性分析[J].煤矿机械,2006,27(11)：68-69
[299]彭斌,刘振全,王君,等.变频涡旋压缩机转子的平衡研究[J].振动工程学报,2004,17(S)：181-183
[300]刘振全,李海生,陈英华,等SolidWorks在涡旋压缩机动平衡计算中的应用[J].流体机械,2005,33(2)：39-41
[301]刘振全,李海生,陈英华.基于Pro/E和VB的涡旋压缩机动平衡计算[J].兰州理工大学学报,2005,31(5)：61-63
[302]王呼佳,陈洪军ANSYS工程分析进阶实例[M].北京：中国水利水电出版社,2006
[303]李浩月,周田朋,刘相新AN SYS工程计算应用教程[M].北京：中国铁道出版社,2003
[304]李泽天,王兴伟,李小飞.基于ANSYS的轴承座有限元分析[J].兵工自动化,2008,27(12)：94-96
[305]王富耻,张朝辉ANSYS 10.0有限元分析理论与工程应用[M].北京：电子工业出版社,2006
[306]刘厚林,徐欢,王凯,等,基于流固耦合的余热排出泵转子模态分析[J].流体机械,2012,40(6)：28-32
[307]骆天舒,戴韧.整体式向心叶轮模态的有限元分析[J].内燃机工程,2005,26(1)：77-80
[308]赵经文,王宏钰.结构有限元分析[M].北京：哈尔滨工业大学出版社,1988
[309]王天煜,王凤翔,方程,等.高速电机转子临界转速计算与振动模态分析[J].辽宁 工程技术大学学报：自然科学版,2009,28(5)：805-808
[310]闻邦椿,顾家柳,夏松波,等.高等转子动力学—理论、技术及应用[M].北京：机械工业出版社,2000
[311]钟一谔,何衍宗,王正,等.转子动力学[M].北京：清华大学出版社,1987
[312]王孚懋,李东敬,杨龙,等.罗茨鼓风机转子系统动态特性分析[J].机械设计与制造,2010,(5)：152-154
[313]刘国庆,杨庆东ANSYS工程应用教程：机械篇[M].北京：中国铁道出版社,2003
[314]徐宇平,袁寿其,张金凤,等.ZJ-200-25型螺旋离心泵转子静力学分析[J].排灌机械工程学报,2012,30(3)：254-258
[315]陈果.航空发动机整机耦合动力学模型及振动分析[J].力学学报,2010,42(3)：548-559
[316]申苗,唐驾时,李克安,等.航空发动机双转子系统的模态分析[J].兵工自动化,2010,29(2)：34-36
[317]夏长高,王凌云.车用内燃机曲柄连杆机构动力学分析[J].拖拉机与农用运输车,2004,(5)：29-31
[318]朱海荣,彭培英.基于ADAMS的往复式压缩机运动机构仿真研究[J].机械设计与制造,2010,32(9)：83-84
[319]Aoyama T, Inagaki M,Kawamoto A, et al.Analysis of main bearing force and cylinder block vibration related toengine air borne noise[J].JSAE Review, 2002, 21: 404-406
[320]郝志勇,段秀兵,宋宝安,等.车用柴油机曲轴系统动力学仿真[J].农业机械学报,2005,36(7)：4-7
[321]程金林.基于机体低噪声虚拟设计的曲轴系统耦合动力学研究[D].天津：天津大学,2003
[322]李超,余洋,赵嫚.涡旋压缩机虚拟建模与运动仿真[J].流体机械,2012,40(1)：17-21
[323]张晓君,张波.涡旋压缩机传动系统动平衡研究与优化[J].机械设计与制造,2012,(4)：149-151
[324]戴旭东,王义亮,袁小阳,等.多缸内燃机缸体瞬态动力分析[J].内燃机学报,2003,21(3)：277-282
[325]李俊宝,杨庆佛.柴油机机体振动响应有限分析[J].内燃机工程,1995,16(3)：9-16
[326]Kim,H.J. etal.Balance Weight Design for a Radially Compliant Scroll Compressor. Proc of 1997 Int Compressor Eng Conf at Purdue PP.232-239
[327]彭斌,刘振全.变频涡旋压缩机转子的平衡研究[J].振动工程学报,2004,17(1)：181-183
[328]申永胜.机械原理教程[M].北京：清华大学出版社,2005
[329]刘振全.涡旋式流体机械与涡旋压缩机[M].北京：机械工业出版社,2009
[330]樊林,靳春梅,屈宗长,等.通用型线涡旋压缩机的误差及运动分析[J].机械工报,2002,6(38)：140-143
[331]樊林,耿森林,靳春梅.涡旋压缩机机构统一模型的研究[J].机械科学与技术,2000,5(19)：755-757
[332]时冰.600MW超临界汽轮机再热主汽阀门动力学建模与虚拟样机研究[D].上海：上海交通大学博士论文,2008
[333]阎绍泽,陈鹿民,季林红,等.含间隙较的机械多体系统动力学模型[J].振动工程学报,2003,16(3)：290-294
[334]时冰,金烨.面向虚拟样机的机构间隙旋转铰建模与动力学仿真[J].机械工程学报,2009,45(4)：299-303
[335]白争锋.考虑铰间间隙的机构动力学特性研究[D].哈尔滨工业大学博士论文,2011
[336]Flores P, Ambro J, Claro J C.In:Dynamics analysis for planar multibody mechanical systems with real joints[C].Proceedings of ECCOMAS Thematic Conference on Advances in Computational Mutibody Dynamics. Portugal: Lisbon, 2003:26-41
[337]AMBROSIO J A C.Impact of rigid and flexible multibody systems:Deformation description and contact models[M].Virtual Nonlinear Multibody Systems,Nato Advanced Study Institute, Prague, 2002, 2:15-33
[2]Creux. Rotary Engineer[P]. U.S. Patent,801,182,1905
[3]L.Nordi. Improvements in or Relating to Fluid Pumps and the Like[P].U.K. Patent Specification,220,296. January 8,1925
[4]R.W.Moore,et al.A Scroll Compressor for shipboard Helium Liquefier System[C].In: ICECP, Pudue, USA,1976,417-422
[5][日]荒井信胜,等.涡旋压缩机及其在箱形空调器上的应用[J].压缩机技术,1985,1：55-59
[6]姜尔宁编译.世界制冷压缩机发展趋势(一)[J].制冷技术,2009,2：46-53
[7][美]David Simpsvn.制冷压缩机的发展与动向[J].制冷技术,1995,1：39-43
[8]夏克盛,等编译.世界压缩机发展趋势[J].制冷技术,2001,1：48-53
[9]李红旗编译.世界各国近期压缩机发展概况(二)[J].家用电器科技,2001,6：66-69
[10]http://www.chinairn.com/news/20120720/435528.html.
[11]杨.GMCC涡旋压缩机下线[J].电器,2011,1：63
[12]王焕然,王迪生.喷油涡旋空压机性能试验研究[J].压缩机技术,1992,2：1-4
[13]樊灵,靳春梅,孙国基,等.大排气量涡旋空压机设计的关键技术[J].压缩机技术,2002,1：5-7
[14]江波,王迪生.微型涡旋式空气压缩机背压机构研究[J].流体机械,1996,24(8)：18-22
[15]赵远扬,李连生,束鹏程.喷水涡旋空气压缩机工作特性的研究[J].西安交通大学学报,2004,38(9)：887-890
[16]房师毅,李连生,束鹏程.无油润滑涡旋式空气压缩机的工作过程研究[J].中国机械工程,2005,16(2)：123-127
[17]汪军,唐甜甜,李连生,等.喷水涡旋空气压缩机压缩过程的换热特性分析[J].流体机械,2003,31(11)：7-9
[18]李超,赵荣珍,刘振全,等.涡旋式空气压缩机润滑系统的研究[J].润滑与密封,2004,164(7)：104-105
[19]司玉宝,屈宗长,王迪生.WXA-1/7型涡旋式空气压缩机的开发[J].流体机械,2000,28(10)：14-17
[20]司玉宝,屈宗长,樊灵,等.新型特种涡旋式空压机的研制[J].压缩机技术,1999,(3)：3-5
[21]高秀峰,王彦峰,郁永章.喷油涡旋空压机喷油孔位置的计算[J].流体机械,1999,27(2)：22-26
[22]马一太,刘圣春,曾宪阳.C02涡旋压缩机泄漏分析[J]压缩机技术,2005,3：36-39
[23]郝璟瑛,王智忠,赵远扬.C02涡旋压缩机动力学特性的研究[J].制冷学报,2011,32(5)：42-46
[24]李超,刘振全,赵荣珍.双端面机械密封在涡旋式天然气压缩机中的应用[J].流体机械,2005,35(7)：49-51
[25]顾兆林,高秀峰,李云,等.新型汽油机用废气涡旋增压器德研究[J].小型内燃机,2000,29(3)：1-7
[26]顾兆林,郁永章,刘传李,等.废气涡旋式增压器的理论研究[J].内燃机工程,1996,17(1)：23-28
[27]李连生,郁永章.外燃式涡旋发动机理论分析与研究[J].西安交通大学学报,1994,28(8)：89-93
[28]顾兆林,郁永章,蒋德明,等.一种废气涡旋增压器[P].中国专利,CN94216734.1
[29]顾兆林,郁永章.新型车用废气涡旋增压器的设计研究[J].车用发动机,1995,(5)：34-37
[30]孟铭,倪计民.车用涡旋增压器型线参数的优化计算[J].同济大学学报,2003,31(3)：343-346
[31]倪计民,孟铭,周奇,等.涡旋增压器与发动机匹配的理论计算研究[J].汽车技术,2002,31(10)：15-18
[32]纪民举,李超,刘振全.车用涡旋增压器与发动机匹配的理论研究[J].压缩机技术,2008,3：14-18
[33]纪民举,李超,刘兴旺,等.涡旋增压器背压密封组件的设计研究[J].压缩机技术,2007,4：20-22
[34]马小礼.车用涡旋增压器设计与性能研究[D].兰州理工大学硕士论文,2007
[35]滑赵杰.车用双侧涡旋增压器的设计研究[D].兰州理工大学硕士论文,2008
[36]江波,王迪生,钱立元.SCP-1.08/0.6涡旋式油泵的研制[J].流体机械,1996,24(2)：15-17
[37]赵宇山.涡旋原理的新应用—涡旋泵[J].压缩机技术,1993,2：2-7
[38]Su, Y., Sawada, T., Takemoto, Haga, S. Theoretical study on the pumping mechanism of a dry scroll vacuum pump. Vacuum Pump 1996,6:815-818
[39]Zhu J., et al. Research on the Discharge Port of Scroll Oil Pump. In:ICECP, Pudue, USA,1992,611-621
[40]T. Kushiro, et al. Development of a Scroll-Type Oil-Free VacuumPump[C].In:ICECP, Pudue, USA,1990,147-155
[41]E.Morishita,etal.Rotating Scroll Vacuum Pump[C].In:ICECP, Pudue, USA,1988,198-205
[42]杨旭,张贤明,王立存,等.UG软件在真空泵涡旋盘建模与仿真中的应用[J].真空,2013,50(2)：10-13
[43]杨广衍,滕普光,张鹏,等.涡旋真空泵的设计与操作[J].真空,2006,43(4)：19-22
[44]王志,巴德纯.涡旋真空泵中固体润滑技术的应用研究[J].沈阳航空工业学院学报,2002,9(2)：20-21
[45]王旭迪,胡焕林.涡旋真空泵型线设计[J].合肥工业大学学报(自然科学版),2001,24(1)：103-105
[46]王旭迪,胡焕林.涡旋式真空泵[J].真空与低温,1999,5(1)：32-34
[47]巴德纯,杨乃恒,李树军,等.涡旋干式真空泵结构对抽气性能的影响[J].真空,1999,(1)：8-11
[48]巴德纯,李树军,许寿华,等.涡旋式无油真空泵动力学研究[J].真空,1998,(4)：12-16
[49]孟冬辉.涡旋无油真空泵设计理论及加工工艺的研究[D].东北大学硕士学位论文,2004
[50]王友亮.涡旋无油真空泵抽气过程的计算机模拟[D].东北大学硕士学位论文,2003
[51]李春燕.无油涡旋真空泵内部流场的计算机模拟与仿真[D].东北大学硕士学位论文,2008
[52]黄英,李建军,韩晶雪,等.干式涡旋真空泵的发展与关键问题[J].真空,2013,50(3)：26-29
[53]邵兵.涡旋泵涡旋齿的压力和温度场模型[J].化工机械,2011,38(5)：588-590
[54]屈宗长,樊灵,阎毓.涡旋输油泵泄漏研究[J].压缩机技术,1998,(6)：3-7
[55]屈宗长,江波,王迪生.新型涡旋输油泵[J].压缩机技术,1998,(2)：33-34
[56]江波,朱杰,畅云峰,等.涡旋式油泵的试验分析[J].压缩机技术,1998,(2)：18-20
[57]屈宗长,阎毓,王迪生.涡旋油泵转速的优化[J].压缩机技术,1997,(5)：30-33
[58]Zhu J., et al. Research on the Discharge Port of Scroll Oil Pump[C]. In:ICECP,Pudue, USA,1992,611-621
[59]张贤明,陈栋,王立存,等.滤油机涡旋真空泵泄漏损耗及密封研究[J].真空,2013,50(4)：26-29
[60]顾兆林,郁永章.新型涡旋式机械原理及其在内燃机中的应用(1)[J].小型内燃机,1995,24(6)：51-56
[61]顾兆林,郁永章.新型涡旋式机械原理及其在内燃机中的应用(2)[J].小型内燃机,1996,25(1)：1-5
[62]顾兆林,郁永章,蒋德明.涡旋式内燃机工作过程的分析研究[J].内燃机工程,1998,19(1)：22-27
[63]顾兆林,郁永章,蒋德明.一种新型内燃机—涡旋式发动机的理论研究[J].西安交通大学学报,1995,29(11)：89-95
[64]陈波,沈永年.两相涡旋膨胀机的性能及实验研究[J].深冷技术,2004,(2)：10-12
[65]王向红,沈永年,王洪明.涡旋式膨胀机泄漏损失的数值计算与分析[J].流体机械,2002,30(9)：18-20
[66]刘井龙,熊联友,侯予,等.一种新型膨胀机—涡旋式膨胀机[J].深冷技术,2000,(4)：13-15
[67]沈永年.涡旋式膨胀机热力过程分析与实验研究[J].低温工程,2000,(4)：23-28
[68]陈波.涡旋式膨胀机的热力特性研究[D].浙江大学硕士学位论文.2004
[69]吴锡江.基于涡旋膨胀机的车用小型余热回收系统开发[D].浙江大学硕士学位论文.2011
[70]严雨林.有机朗肯循环系统涡旋膨胀机工作过程分析与实验研究[D].天津大学,2011
[71]褚晓广,张承慧,李珂,等.涡旋膨胀机发电系统效率优化控制策略[J].电工技术学报,2012,27(6)：25-31
[72]杨兴华,潘家祯,王吉岱,等.涡旋式膨胀机内部流场的数值模拟研究[J].流体机械,2013,41(2)：15-18
[73]屈宗长,朱杰,李心伟,等.多级涡旋压缩机压力比与喷油量的优化[J].西安交通大学学报.1995,29(11)：44-48
[74]Chong, Y.F., et al.A Two Stage Double Acting Scroll Air Compressor. In:ICECP. Pudue, USA,1994:659-663
[75]徐虹玲.并联涡旋式压缩机油平衡特性的试验研究[J].制冷与空调,2013,13(5)：55-57
[76]吴伟军,钟建法,彭仟能.并联涡旋式压缩机在空气源热泵机组中的应用分析[J].制冷与空调,2013,13(1)：55-58
[77]顾兆林,郁永章,蒋德明.双涡圈及多涡圈涡旋机械几何特性的理论研究[J].西安交通大学学报,1998,32(12)：90-93
[78]顾兆林.双涡圈涡旋压缩机理论及应用研究[D].西安交通大学博士论文,1997
[79]刘卫华,高秀峰,冯诗愚,等.双涡圈涡旋机械修正齿形的基元面积计算[J].西安交通大学学报,2002,36(11)：1195-1198
[80]王君,赵嫚,刘兴旺,等.多涡旋齿涡旋压缩机的可用啮合型线研究[J].压缩机技术,2005,6：7-10
[81]王君.多涡旋齿涡旋压缩机啮合型线理论研究[D].兰州理工大学博士论文,2006
[82]Takashi B. etal.Fuel Cell System Having Scroll Type Compressor and Regenerator.Patent:US6361890,2002
[83]Takashi B., et al.Fuel Cell System Having Common Scroll Type Compressor and Regenerator.Patent:US6338912,2002
[84]Zhao Yuanyang, et al.Research on oil-free air Scroll Compressor with high speed in 30 KW fuel cell. Applied Thermal Engineering,2003,23:593-603
[85]C. F. Lai,et al. The Development of Oil-less Scroll Compressor Used for Fuel Cells[C]. Proc. of the 4th International Conference on Compressor and Refrigeration at Xi'an,2003,241-249
[86]李海生.无油润滑涡旋压缩机的研究[D].兰州理工大学硕士论文,2005
[87]李超,刘振全,王君.燃料电池用无油润滑涡旋压缩机研究[J].润滑与密封,2008,33(6)：74-76
[88]邱凯,徐博,乔宗亮.空调用涡旋压缩机背压腔变频特性的实验研究[J].压缩机技术,1997,4：3-5
[89]伍光辉.基于数码涡旋压缩机的空调系统的研究[D].华中科技大学博士论文,2004
[90]彭斌,刘振全,张洪生,等.变频涡旋压缩机的研究与应用[J].兰州理工大学学报,2005,31(1)：60-63
[91]樊灵,屈宗长,靳春梅等.汽车空调用涡旋压缩机变容量调节机构的研究[J].流体机械,1999,27(11)：47-49
[92]廖全平,李红旗.涡旋变频压缩机[J].流体机械,2002,30(2)：35-37
[93]王贻任,Arup Majumdar美国谷轮公司压缩机应用技术讲座,第九讲数码涡旋技术[J].制冷技术,2003,1：35-38
[94]魏栋,梁荣光,萨比特.先进的数码涡旋制冷压缩机技术.低温与特气[J].2006,24(4)：6-9
[95]王宝龙,韩林俊,石文星,等.基于制冷剂泄出的涡旋压缩机容量调节技术[J].制冷学报,2010,31(2)：7-10
[96]李庆伟,刘强.下一代数码涡旋压缩机技术[C].2010年国际制冷技术交流会论文集,2010.8.6
[97]陈斌,陈光明,刘利华,等.混合工质变容量调节技术及其应用[J].流体机械,2004,32(12)：64-68
[98]刘兴旺.提高变频涡旋压缩机压缩性能的方法研究[D].兰州理工大学博士论文,2011
[99](日)森下悦生,等.邓立文译.涡旋压缩机的几何理论.流体工程,1985,(10)：38-48
[100](日)森下悦生,杉原正浩.涡旋压缩机的设计问题[J].压缩机技术,1988,4：11-20
[101]M.Hayano.Performance Analysis of Scroll compressor for Air Conditioner[C].In: ICECP, Pudue, USA,1986, (2):836-871
[102]黄允东,郁永章.半圆片偏心线涡旋压缩机的几何理论[J].压缩机技术,1997,1：3-6
[103]K.Tojo, et al. New Wrap profile for Scroll Type Machine[C]. Proceedings of 19th International Congress of Refrigeration, Hague, The Netherlands,1995(3a):515-521
[104]H.Kohsokable, et al. Study on Scroll Profile Based on Algebraic Spiral for Scroll Fluid Machine[J]. Transactions of the JAR,1994(11), No.3:337-347
[105]李连生,郁永章,束鹏程.采用渐开线的涡旋型线理论研究[J].流体机械,1994,22(5)：50-56
[106]李连生.线段渐开线涡旋压缩机的几何理论[J].流体机械,1994,22(12)：22-28
[107]李连生,束鹏程,郁永章,等.涡旋型线对涡旋式压缩机性能的影响[J].西安交通大学学报,1997,31(2)：45-50
[108]Liansheng Li,Pengcheng Shu, Yongzhang Yu. Effect of scroll wraps on performances of scroll compressor[C].In:ICECP. Pudue, USA,1996:579-585
[109]Li,Liansheng, Shu,Pengcheng, Yu,Yongzhang.The effect of scroll wraps on the performance of scroll compressor[J].International Journal of Refrigeration.1997, 20(5):326-331
[110]李连生,束鹏程,黄炯,等.涡旋式压缩机排气系统气流脉动现象研究[J].应用力学学报,1997,14(3)：84-89
[111]李连生,束鹏程.涡旋型线对排气口侵入及排气流速的分析计算[J].西安交通大学学报,2000,32(7)：56-59
[112]王国梁,李连生,张薇,等.一种新型涡旋型线的几何理论研究[J].西安交通大学学报,2003,37(5)：499-503
[113]王国梁.一种新型涡旋压缩机型线的几何理论及其应用研究[D].西安交通大学博士学位论文,2003
[114]王君,刘振全,李超.涡旋压缩机渐开线和圆弧组合型线的设计计算[J].流体机械,2004,32(10)：10-13
[115]王君,查海滨,张晓慧,等.一种渐变啮合间隙的变壁厚涡旋齿型线研究[J].工程热物理学报,2013,34(8)：1453-1456
[116]J.W.Bush,et al.Derivation of general relation governing the conjugate of scroll profile[C].In:ICECP. Pudue, USA, 1992,1079-1088
[117]J.W.Bush,et al.Maximizing Scroll Compressor Displacement Using Generalized Wrap Geometry[C].In:ICECP. Pudue, USA, 1994, 205-210
[118]畅云峰,朱杰,江波,等.涡旋压缩机啮合理论及通用型线控制方程[J].压缩机技术,1998,2：12-13
[119]樊灵,靳春梅,屈宗长,等.通用型线涡旋压缩机的误差及运动分析[J].机械工程学报,2002,38(6)：139-143
[120]樊灵,靳春梅,屈宗长,等.涡旋压缩机型线的误差灵敏度与径向啮合间隙的相关分析[J].机械工程学报,2003,39(4)：151-154
[121]屈宗长,樊灵,王迪生.通用型线涡旋压缩机的几何理论[J].西安交通大学学报.1999,33(11)：39-42
[122]樊灵.涡旋压缩机型线通用数学模型及实验研究[D].西安交通大学博士学位论文,2000
[123]刘涛,邬再新,刘振全.法向等距线法生成涡旋压缩机型线的研究[J].机械工程学报,2004,40(6)：55-58
[124]T.Hirano.Scroll profiles for scroll fluid machines[J].MHI Tech Rev, 1990, 27(1): 35-41
[125]T.Hirano.Scroll - type fluid machine with specific inner curve segments[P].Patent:US 4856973,1989
[126]朱杰.涡旋压缩机径向柔性机构的研究[D].西安交通大学博士学位论文,1994
[127]朱杰,江波,畅云峰,等.涡旋压缩机高压区型线的优化研究[J].压缩机技术,1998,2：7-8
[128]朱杰,畅云峰,江波,等.涡旋压缩机一种优化型线的几何理论[J].压缩机技术,1998,2：43-46
[129]Lee, et al.On the Profile Design of a Scroll Compressor[J].International Journalof Refrigeration,1995,18(5):308-317
[130]刘振全,杜桂荣,於时才.涡旋式压缩机涡旋齿修正的新方法[J].甘肃工业大学学报,1990,16(4)：1-6
[131]刘振全,於时才,杜桂荣.涡旋压缩机涡旋齿修正的图解法和修正角的研究[J].制冷学报,1992,52(2)：6-10
[132]Liu Zhenquan, Du Guirong, Yu shicai, et al.The graphic method of modified wrap of scroll compressor[C].In:ICECP. Pudue, USA,1992:1099-1106
[133]Liu Zhenquan, Du Guirong,Yu Shicai.The mathematical derivation and analysis of the graphic method for wrap modification of the scroll compressor[C].In:Proc. of the 93th International Compressor Technique Conference.Sponsored by Xi'an Jiaotong University,Xi'an, China.1993:482-489
[134]Liu Zhenquan, Du Guirong, Qi Zhiyong, etal.The conjugacy analysis of modified part of scroll profiles. In:ICECP. Pudue, USA,1994:479-484
[135]Wang Baolin, Li Xianting, Shi Wenxing.A General Geometrical Modle of Scroll Compressors Based on Discretional Initial Angles of Involute[J].International Journal of Refrgeration,2005,28:958-966
[136]冯诗愚,顾兆林,李云.涡旋机械的涡旋体始端型线研究[J].西安交通大学学报,1998,32(1)：88-92
[137]高秀峰,冯诗愚,顾兆林,等.涡旋齿端不等β角圆弧类型线修正研究[J].西安交通大学学报,1999,33(12)：56-60
[138]高秀峰,冯诗愚,顾兆林,等.对称圆弧修正齿型涡旋压缩机排气孔的开设分析[J].西安交通大学学报,2000,34(6)：89-92
[139]高秀峰,刘卫华,冯诗愚,等.涡旋齿端等p角圆弧类型线修正理论的研究[J].西安交通大学学报,2001,35(7)：750-754
[140]高秀峰.涡旋压缩机齿形修正及排气孔研究[D].西安交通大学博士学位论文,2000
[141]王君,刘振全.双涡圈涡旋压缩机完全啮合型线修正理论研究[J].机械工程学报,2005,41(3)：234-238
[142]王君,刘振全.涡旋压缩机渐开线类型线的双圆弧修正[J].机械工程学报,2005,41(9)：202-206
[143]王君,刘振全.涡旋压缩机双圆弧修正解析法设计及误差分析[J].上海交通大学学报,2005,39(9)：1418-1421
[144]王君,刘振全.涡旋压缩机渐开线型线的多对圆弧修正[J].北京理工大学学报,2005,25(9)：757-760
[145]王君,刘振全.多涡旋齿涡旋压缩机型线的双圆弧修正研究[J].中国机械工程,2006,17(15)：1553-1556
[146]王伟.涡旋压缩机涡旋新型线及系统动力学研究[D].重庆大学硕士论文,2004
[147]宋立权,陈进,王伟.基于三基圆的涡旋压缩机型线研究[J].中国机械工程,2005,16(16)：1458-1461
[148]Liu tao, Liu zhenquan. Study on Geometry Theory of Trigonometric-curve Modification of Scroll Compressor[C]. In:ICECP. Pudue, USA,2004, CO43
[149]刘振全,杜桂荣.涡旋压缩机理论机构模型[J].机械工程学报,1999,35(2)：38-41
[150]Liu Zhenquan, Tadashi, Yanagisawa.A Mechanical Model For The Scroll Mechanism And Its Kinematical Analysis. In:ICECP. Pudue, USA,1998:507-512
[151]刘振全,柳泽正.涡旋机械的机构模型及理论分析[J].甘肃工业大学学报,1996,22(2)：36-42
[152]杜桂荣,刘振全.涡旋压缩机机构模型及径向随变调节原理[J].制冷学报,1997,2：1-7
[153]周家胜.公转型与回转型涡旋流体机械[J].压缩机技术,1997,5：12-13
[154]周莺.回转型涡旋流体机械[J].压缩机技术,2004,1：30-32
[155]樊灵,靳春梅,屈宗长,等.基于四杆机构的涡旋压缩机的平衡分析[J].机械设计,2000,2：42-44
[156]Barito, Yu Chen.Analysis for Development of the Ant-Rotational Roller Clutch Device for Scroll Compressor[C].In:ICECP. Pudue, USA,1996:451-457
[157]周家胜.涡旋压缩机防自转机构[J].压缩机技术,1995,3：5-10
[158]杜桂荣,刘振全,秦子荣.涡旋式压缩机的防自转机构[J].甘肃工业大学学报1991,17(3)：1-6
[159]Pierre Ginies, Christophe Ancel and Remi Bou Dargham.Three-Crankshaft-Driven Scroll Compressor[C]. In:ICECP. Purdue, USA.2006:C144
[160]刘振全,赵嫚,李超.涡旋压缩机曲柄销防自转机构分析[J].兰州理工大学学报,2006,32(4)：53-55
[161]赵嫚.涡旋压缩机机构动力特性的研究[D].兰州理工大学硕士学位论文,2006
[162]李超,单彩侠,余鹏飞,等.涡旋压缩机小曲拐防自转机构的动力特性[J].兰州理工大学学报,2008,34(1)：50-53
[163]郑尚书.无油润滑涡旋压缩机防自转机构动力特性研究[D].兰州理工大学硕士论文,2013
[164]朱杰.涡旋压缩机径向柔性机构的研究[D].西安交通大学博士学位论文,1994
[165]李吉功.空调用涡旋压缩机的径向柔性机构研究及整机CAD软件开发[D].兰州理工大学硕士论文,1997
[166]翟俊霞.涡旋压缩机随变机构的研究[D].兰州理工大学硕士论文,1998
[167]李超,赵荣珍,刘振全.涡旋压缩机径向随变机构动力学模型研究[J].压缩机技术,2004,3：7-8
[168]刘涛,杜桂荣,邬再新.涡旋压缩机的径向柔性密封机构[J].机械工程师,1999,11：6-7
[169]刘涛,邬再新.一种涡旋压缩机径向随变机构的设计[J].流体机械,2001,29(7)：17-19.
[170]李元鹤.涡旋式压缩机轴向柔性机构的研究[D].西安交通大学博士学位论文,2000
[171]赵兴艳,刘振全.具有双背压腔涡旋压缩机的研制[J].甘肃工业大学学报,1999,25(1)：50-54
[172]屈宗长,王开宁,李元鹤,等.背压平衡涡旋压缩机传热学研究[J].陕西工学院学报,1998,14(1)：38-44
[173]高秀峰,郁永章.涡旋压缩机二次平衡及背压孔研究[J].流体机械,1999,27(7)：15-19
[174]屈宗长,李心伟,李绍平.背压平衡涡旋压缩机的研究[J].西安交通大学学报,1998,32(7)：51-55
[175]Zhu Jie, et al.Research on Self Adjusting Back-pressure Mechanism of Scroll Compressor[C].In:ICECP.Purdue,USA,1992:1137-1145
[176]Zhu Jie, et al. Theoretic Model of Back-pressure Chamber for Scroll Compressor[C]. In:ICECP. Purdue, USA,1992:1127-1135.
[177]Toji, I.Hayase. Self-adjusting Back Pressure Mechanism for Scroll Compressor[C].In: ICECP. Purdue, USA,1988:901-906
[178]唐光德,王文彦,许修铭.涡旋式压缩机轴向柔性补偿机构设计[J].制冷与空调,2006,2(6)：34-37
[179]Nieter J J.Dynamic of compliance mechanisms in scroll compressors part 1:Axial compliance[C].In:ICECP. Purdue, USA, 1990:173-182
[180]J.Niete.Dynamics of Compliance Mechanisms in Scroll Compressors Part 1: Axial Compliance[C].In:ICECP. Purdue, USA, 1992:309-316
[181]T.Shu, et al.Dynamics of Orbiting Scroll with Axial Compliance, Part 1: Simulation of Orbited Axial Motion[C]. In:ICECP. Purdue, USA,1992:861-870
[182]J. Marchese, et al.Dynamics of Orbiting Scroll with Axial Compliance, Part 2: Experimental Techniques[C]. In:ICECP. Purdue, USA, 1992:871-882
[183]W. Bush, et al.General Stability and Design Specification of the Back-pressure Supported Axially Compliant Orbiting Scroll[C].In:ICECP. Purdue, USA, 1992:853-860
[184]Noriaki Ishii, Kenichi Bird, Kiyoshi Sano, et al. Refrigerant leakage flow evaluation for scroll compressors[C]. International Compressor Engineering Conference at Purdue University, West Lafayette, Indiana, USA:1996:633-638
[185]Cko Namkyu, Yang Young, Lee Byung Chul, et al.The characteristics of tangential leakage in scroll compressors for air conditioners[C].In:ICECP. Purdue, USA, 2000, Volume I:807-814
[186]Itoh Takahide et al. Leakage characteristics of scroll compressor by two phase flow model in consideration of wall oil film thickness[J].Transactions of the Japan Society of Mechanical Engineers, Part B, 2002, 68:671
[187]朱杰.涡旋压缩机的泄漏模型及性能计算机程序[J].制冷学报,1992(4)：15-18
[188]江波,畅云峰,朱杰,等.涡旋压缩机内部泄漏的流态分析[J].压缩机技术,1998,(2)：21-23
[189]李力,张占收,边红卿.涡旋压缩机径向间隙的泄漏[J].河北工业科技,1999,16(55)：17-23
[190]屈宗长,孙存慧,司玉宝,等.涡旋压缩机中气体泄漏的估算[J].压缩机技术,1998,(2)：35-37
[191]李超,梁秋立,赵嫚.表面粗糙度对无油润滑涡旋压缩机微间隙泄漏的影响[J].流体机械,2011,39(4)：40-43
[192]李超,赵荣珍,刘振全.涡旋压缩机机构误差对密封间隙的影响[J].润滑与密封,2007,32(7)：66-71
[193]刘兴旺,田玉恒,刘振全,等.涡旋压缩机轴向间隙中流体在层流流态下的泄漏研究[J].流体机械,2004,32(7)：9-11
[194]刘兴旺,赵嫚,李超,等.涡旋压缩机的径向迷宫密封研究[J].机械工程学报,2012,48(21)：97-104
[195]K.Jang, S.Jeong.Experimental investigation on convective heat transfer mechanism in a scroll compressor[J].International Journal of Refrigeration, 2006, 29:744-753
[196]R.J.Rogers, et al.Scroll Compressor Flow Modeling: Experimental and Computational Investigation[C]. In:ICECP. Pudue, USA, 1990:206-215
[197]G.H.Lee.Performance Simulation of Scroll Compressors[J].Proceedings of the Institution of Mechanical Engineers Vol 216 Part A:Journal of Power and Energy. 2002:169-179
[198]E. Morishita, et al. Scroll Compressor Analytical Model[C]. In:ICECP. Pudue, USA, 1984:487-495
[199]Ooi, Kim Tiow, Zhu, Jiang.Convective Heat Transfer in a Scroll Compressor Chamber:a2-D Simulation[J].International Journal of Thermal Sciences.2004,43(7): 677-688
[200]S.Pietrowicz,etal. Mathematical Modeling of Physical Processes in the Scroll Compressor Chamber[J].In:ICECP. Pudue, USA,2002, C20-6
[201]K. T. Ooi,et al. Convective heat transfer in a scroll compressor chambena 2-Dsimulation[J].International Journal of Thermal Sciences,2004,43:677-688
[202]Y. Chen,et al. Mathematical Modeling of Scroll Compressors-Part I:Compression Process Modeling[J].International Journal of Refrigeration,2002,25:731-750
[203]Y. Chen, et al. Mathematical Modeling of Scroll Compressors-Part Ⅱ:Overall Scroll Compressor Modeling[J].International Journal of Refrigeration, 2002, 25: 751-764
[204]冯健美.涡旋式空气压缩机排气孔工作特性研究和排气流动的三维数值模拟计算[D].西安交通大学博士论文,2003
[205]冯健美,屈宗长,李心伟.涡旋压缩机排气过程的三维数值模拟计算[J].西安交通大学学报,2004,38(11)：1141-1146
[206]E.Morishita, et al.Scroll Compressor Analytical Model[C].In:ICECP.Pudue, USA,1984,487-495
[207]N. Ishii, et al.A Study On Dynamic Behavior of A Scroll Compressor[C].In:ICECP. Pudue, USA,1986,901-916
[208]N. Ishii, et al.On The Superior Dynamic Behavior of Variable Rotating Speed Scroll Compressor[C].In:ICECP. Pudue, USA,1988,75-82
[209]林隐虎.涡旋压缩机的力学模型[J].压缩机技术,1991,6：1-8
[210]吴建华,束鹏程.涡旋压缩机的动力分析[J].制冷学报,1995,(4)：1-8
[211]司玉宝,屈宗长,王迪生.涡旋压缩机型线动力特性的研究[J].西安交通大学学报,2000,34(11)：53-56
[212]刘振全,高艳,王君.双头涡旋齿涡旋压缩机气体力分析[J].制冷学报,2005,26(3)：42-46
[213]R.Williams, et al.Scroll Compressor with No Tipping Moment[C].In:ICECP. Pudue, USA,1998:165-173
[214]Liu tao, Liu zhenquan.Investigation of scroll compressor with no overturning moment[C].In:Proc. of the 2003'International Compressor Technique Conference. Sponsored by Xi'an Jiaotong University, Xi'an, China,2003,128-132
[215]Li Chao, Liu zhenquan.The study of characteristics with smaller overturning moment for scroll compressor[C].In:ICECP. Pudue, USA,2004,12-15
[216]樊灵,耿森林,屈宗长,等.涡旋压缩机的平衡分析[J].机械科学与技术,2000,6：935-937
[217]柏杰,李连生,郁永章.涡旋式压缩机动力特性分析[J].西安交通大学学报,1994,28(8)：83-88
[218]J.Kim, et al.Design of Phase-angled Balance Weights for an Inverter Driven Scroll Compressor[C].In:ICECP. Pudue, USA,1998:749-745
[219]刘振全,任俊士.涡旋压缩机的振动时域和频域分析[J].甘肃工业大学学报,2000,26(1)：49-53
[220]刘振全,任俊士.立式涡旋压缩机的振动分析[J].流体机械,2000,28(1)：20-23
[221]周雷,金光喜,谢友柏,等.无油压缩机滑动轴承磨损过程的动态模拟[J].润滑与密封,1996,6：28-30
[222]曹霞,陈芝久,刘振全.立式高压型涡旋压缩机摩擦副分析[J].上海交通大学学报,2000,34(9)：1228-1231
[223]刘兴旺,刘振全,李超等.涡旋压缩机摩擦损耗和泄漏损耗研究[J].压缩机技术,2006,(3)：1-4
[224]焦瑜.基于分形理论的无油润滑涡旋压缩机端面摩擦问题研究[D].兰州理工大学硕士论文,2011
[225]张静.无油润滑涡旋压缩机的摩擦学问题研究[D].兰州理工大学硕士论文,2012
[226]李超,焦瑜,张静,等.动静涡旋端面摩擦副摩擦力分形预测模型[J].化工学报,2012,63(8)：2524-2530
[227]彭斌,孙迎,张力.变截面涡旋压缩机几何模型及摩擦损失模型[J].兰州理工大学学报,2012,38(3)：34-38
[228]T.Drost.Analytical and Experimental Investigation of a Scroll Compressor Lubrication System[C].In:ICECP. Pudue, USA,1992:551-560
[229]Shozo Hase, et al.Development of the High Efficiency Horizontal Type Scroll Compressor[C]. In:ICECP. Pudue, USA,1996:447-452
[230]Sano, et al.A High Reliability Study of Scroll Compressor[C].In:ICECP. Pudue, USA,1996:199-204
[231]赵兴艳,刘振全.涡旋压缩机润滑系统润滑油量优化分析[J].甘肃工业大学学报,1997,23(2)：37-41
[232]Michael M. Cui. Investigation on the Oil Supply System of a Scroll Compressor[C]. ICECP. Pudue, USA,2004, C093
[233]李超,赵荣珍,刘振全,等.涡旋式空气压缩机润滑系统的研究[J].润滑与密封, 2004,164(7)：104-105
[234]王君,李超,马小礼,等.涡旋压缩机工作腔润滑油密封的实验研究[J].润滑与密封,2006,3：100-103
[235]Park, Youn Cheol, Kim,Yongchan, Cho, Honghyun.Thermodynamic Analysis on the Performance of a Variable Speed Scroll Compressor with Refrigerant injection[C]. International Journal of Refrigeration. 2002, 25(8):1072-1082
[236]Dutta, Asit K.,Yanagisawa, Tadashi, Fukuta, Mitsuhiro.An Investigation of the Performance of a Scroll Compressor under Liquid Refrigerant Injection[J]. International Journal of Refrigeration, 2001,24(6):577-587
[237]Cho, Honghyun, Chung, Jin Taek, Kim, Yongchan. Influence of Liquid Refrigerant Injection on the Performance of an Inverter-driven Scroll Compressor[J].International Journal of Refrigeration, 2003, 26(1):87-94
[238]T.Hirano, et al.The Scroll Compressor with variable Capacity Control Mechanism for Automotive Air Conditioner[C].In: ICECP. Pudue, USA,1990:121-130
[239]Kawabe, et al.Development of 2 in 1 Type Scroll Compressor[C].In: ICECP. Pudue, USA,1992:593-601
[240]尚广庆,孙春华.基于UG的涡旋压缩机涡盘设计和制造[J].煤矿机械,2007,28(5)：98-100
[241]乔宗亮,胡志平.涡旋压缩机涡旋盘加工中若干问题探讨[J].压缩机技术,1993,2(118)：14-17
[242]李心伟,江波,冯健美.涡旋压缩机型线加工方法分析(上)[J].数控加工技术,2002,11：29-30
[243]谢利昌.涡旋压缩机大批量生产的几个关键技术问题[J].机械设计与制造,2000,5：32-35
[244]Jiang, Z., Harrison, D.K., Cheng, K. Computer-aided Design and Manufacturing of Scroll Compressors[J]. Journal of Materials Processing Technology. 2003, 1:145-151
[245]王涛,桑伟波,蒋立军.涡旋盘在普通加工中心上的编程加工[J].压缩机技术,2006,(2)：36-37
[246]王平,魏晓伟,安家菊.汽车空调涡旋盘快速硬质阳极氧化处理工艺研究[J].汽车技术,2006,(8)：30-33
[247]王训杰,刘勇,李菊华.UG软件在涡旋压缩机涡旋盘设计与加工中的应用[J].机床与液压,2010,38(8)：35-37
[248]房怀英,杨建红.涡旋压缩机定子加工位置偏差的快速测量[J].华侨大学学报(自然科学版),2010,31(5)：491-495
[249]查谦,查世樑.涡旋压缩机涡旋盘的精加工[J].压缩机技术,2012,(4)：38-40
[250]刘四虎,熊则男,朱均.一种对涡旋体线轮廓度误差进行评价的新方法[J].西安交通大学学报,1996,30(7)：19-24
[251]欧阳林子,陈仰贤,苏建宁,等.一种检测涡旋压缩机涡旋盘的新方法[J].甘肃工业大学学报,2000,30(4)：34-37
[252]李凤宇,欧阳林子,陈仰贤,等.涡旋体加工质量的检测[J].中国机械工程,2002,13(24)：2094-2096
[253]李灿杰.基于振动信号的涡旋压缩机噪声检测系统研究[D].大连理工大学硕士论文,2010
[254]文雅珊.涡旋压缩机主要零部件检测装置设计[D].南昌大学硕士论文,2012
[255]罗伟.涡旋压缩机装配线规划及其部件检测装置设计[D].南昌大学硕士论文,2012
[256]刘强飞.涡旋压缩机定盘面轮廓度检测技术研究[D].南昌大学硕士论文,2012
[257]M. E. Marler, K. B. Kumar. Determination of Scroll Wrap Contact Stress Using the Boundary Element Method[C]. In:ICECP. Pudue, USA, 1992:1117-1125
[258]陈志澜,乔宗亮,熊则男.涡旋压缩机HFC替代工质的研究[J].制冷学报,1995,(1)：1-4
[259]Kohayakawa, et al. Performance Evaluation of Horizontal Type Scroll Compressor for Alternative Refrigerant(R410A) [C]. In: ICECP. Pudue, USA,1998:435-440
[260]刘振全,戚智勇.涡旋压缩机动涡盘应力及变形的研究[J].流体机械,1995,23(10)：23-26
[261]金丹,陈旭,田涛.非均匀温度场下涡旋压缩机动涡盘的盈利及变形分析[J].流体机械,2003,6(31)：11-14
[262]Guir du, Tao Liu,Boxian Qiu, et al.The FEM Analysis of Ahell of Acroll Compressor[C].Proceedings of the 2001'International Compressor Technique Conference.Sponsored by Xi'an Jiaotong University, Xi'anChina,2001:248-253
[263]强建国.涡旋压缩腔几何模型与涡旋齿强度研究[D].兰州理工大学博士论文,2007
[264]王君,张娜,刘凯.基于流场模拟的涡旋压缩机涡齿应力变形分析[J].工程热物理学报,2012,33(8)：1334-1337
[265]Takahide Itoh, Akoto Fujitani, Kimiharu Takeda. Investigation of Discharge Flow Pulsation in Scroll Compressors[C].In: ICECP. Pudue, USA, 1994:683-688
[266]W. Bush, et al.Controlling Discharge Valve Closing Impact in Scroll Machine[C].In: ICECP. Pudue, USA,1998:631-636
[267]王珍,赵之海,杨春立,等.涡旋压缩机振动噪声特性的应用研究[J].压缩机技术,2005,(5)：17-19
[268]屈宗长,李元鹤,王开宁,等.转速对涡旋压缩机性能的影响[J].陕西工学院学报,1997,13(4)：32-37
[269]刘兴旺,姚淑婷,张天龙,等.转速对变频涡旋压缩机压缩性能的影响研究[J].流体机械,2011,39(10)：4-9
[270]邓定国,束鹏程.回转压缩机[M].北京：机械工业出版社,1989
[271]顾兆林,郁永章,冯思愚.涡旋压缩机及其他涡旋机械[M].陕西：陕西科学技术出版社,1998
[272]熊则男,乔宗亮.压缩机设计中的力学分析[M].北京：机械工业出版社,1997
[273]熊则男,乔宗亮.回转压缩机与泵[M].北京：机械工业出版社,1995
[274]N. Ishii,et al.A Study on Danamic Behavior of a Scroll Compressor[C].In:ICECP. Pudue, USA,1986:901-916
[275]H. Iwata,et al. Prediction of Noise from a Scroll Machine[C].In:ICECP.Pudue, USA,1992:977-986
[276]H. Ishii, et al. On the Superior Dynamic Behavior of a Variable Rotating Speed Scroll Machine[C].In:ICECP.Pudue,USA,1988:75-82
[277]李连生.涡旋压缩机[M].北京：机械工业出版社,1995
[278]郁永章.容积式压缩机技术手册[M].北京：机械工业出版社,2000
[279]J.J.Nieter,etal. Counterweighting Scroll Compressor for Minmal Bearing Loads[C].In: ICECP. Pudue, USA,1988:175-181
[280]郭卫东.虚拟样机技术与ADAMS应用实例教程[M].北京：北京航空航天大学出版社,2008.
[281]朱海荣,彭培英,王群辉.基于ADAMS的往复式活塞式压缩机运动机构仿真研究[J].机械设计与制造,2010,32(9)：83-84
[282]白亮亮,唐良宝.基于ADAMS活塞压缩机动平衡虚拟设计[J].流体机械,2008,36(6)：43-45
[283]单彩霞.涡旋压缩机防自转机构动力特性的研究[D].兰州理工大学硕士学位论文,2008,33-34
[284]李超,赵荣珍,刘振全.驱动轴承内嵌式涡旋压缩机特性分析[J].制冷学报,2006, 27(2)：44-47.
[285]孟铭,倪计民.车用涡旋增压器型线参数的优化计算[J].同济大学学报,2003,31(3)：343-346
[286]顾兆林,郁永章,蒋德明.涡旋式内燃机工作过程的分析研究[J].内燃机工程,1998,19(1)：22-27
[287]ZhaoYuanyang et al.Research on oil-free air scroll compressor with high speed in 30 KW fuel cell[J].Applied Thermal Engineering,2003,23:593-603
[288]顾兆林.涡旋压缩机及其它涡旋机械[M].西安：陕西科学技术出版社,1998
[289]刘延柱,陈文良,陈立群.振动力学[M].北京：高等教育出版社,1998
[290]王娅卫,任兴民,秦卫阳,等.转子系统动力特性分析[J].机械科学与技术,2002,21(1)：49-51
[291]Wu JJ, Whittaker A R. Cartmell M P. Dynamic Responses of Structures to Moving Bodies Using Combined Finite Element and Analytical Meth[J]. International Journal of Mechanical Sciences,2001,43(11):2555-2579
[292]王云,雷娜.旋转冲压发动机冲压转子振动模态分析[J].南昌航空大学学报,2008,22(2)：22-25
[293]杜桂荣,刘涛.涡旋式压缩机动涡旋有限元分析方法[J].机械工程学报,1999,35(4)：99-102
[294]郝璟瑛,王智忠,赵远扬,等.C02涡旋压缩机动力学特性的研究[J].制冷学报,2011,32(5)：42-46
[295]胡萍,王珍,赵之海,等.基于模态分析的涡旋压缩机主轴固有特性研究[J].压缩机技术,2007,31(6)：5-7
[296]王君,张娜,刘凯,等.基于流场模拟的涡旋压缩机涡齿应力变形分析[J].工程热物理学报,2012,33(8)：1334-1337
[297]张晓君,张波.涡旋压缩机传动系统动平衡研究与优化[J].机械设计与制造,2012,(4)：149-151
[298]郭仁宁,赵鑫,赵品.涡旋式空气压缩机一次平衡的稳定性分析[J].煤矿机械,2006,27(11)：68-69
[299]彭斌,刘振全,王君,等.变频涡旋压缩机转子的平衡研究[J].振动工程学报,2004,17(S)：181-183
[300]刘振全,李海生,陈英华,等SolidWorks在涡旋压缩机动平衡计算中的应用[J].流体机械,2005,33(2)：39-41
[301]刘振全,李海生,陈英华.基于Pro/E和VB的涡旋压缩机动平衡计算[J].兰州理工大学学报,2005,31(5)：61-63
[302]王呼佳,陈洪军ANSYS工程分析进阶实例[M].北京：中国水利水电出版社,2006
[303]李浩月,周田朋,刘相新AN SYS工程计算应用教程[M].北京：中国铁道出版社,2003
[304]李泽天,王兴伟,李小飞.基于ANSYS的轴承座有限元分析[J].兵工自动化,2008,27(12)：94-96
[305]王富耻,张朝辉ANSYS 10.0有限元分析理论与工程应用[M].北京：电子工业出版社,2006
[306]刘厚林,徐欢,王凯,等,基于流固耦合的余热排出泵转子模态分析[J].流体机械,2012,40(6)：28-32
[307]骆天舒,戴韧.整体式向心叶轮模态的有限元分析[J].内燃机工程,2005,26(1)：77-80
[308]赵经文,王宏钰.结构有限元分析[M].北京：哈尔滨工业大学出版社,1988
[309]王天煜,王凤翔,方程,等.高速电机转子临界转速计算与振动模态分析[J].辽宁 工程技术大学学报：自然科学版,2009,28(5)：805-808
[310]闻邦椿,顾家柳,夏松波,等.高等转子动力学—理论、技术及应用[M].北京：机械工业出版社,2000
[311]钟一谔,何衍宗,王正,等.转子动力学[M].北京：清华大学出版社,1987
[312]王孚懋,李东敬,杨龙,等.罗茨鼓风机转子系统动态特性分析[J].机械设计与制造,2010,(5)：152-154
[313]刘国庆,杨庆东ANSYS工程应用教程：机械篇[M].北京：中国铁道出版社,2003
[314]徐宇平,袁寿其,张金凤,等.ZJ-200-25型螺旋离心泵转子静力学分析[J].排灌机械工程学报,2012,30(3)：254-258
[315]陈果.航空发动机整机耦合动力学模型及振动分析[J].力学学报,2010,42(3)：548-559
[316]申苗,唐驾时,李克安,等.航空发动机双转子系统的模态分析[J].兵工自动化,2010,29(2)：34-36
[317]夏长高,王凌云.车用内燃机曲柄连杆机构动力学分析[J].拖拉机与农用运输车,2004,(5)：29-31
[318]朱海荣,彭培英.基于ADAMS的往复式压缩机运动机构仿真研究[J].机械设计与制造,2010,32(9)：83-84
[319]Aoyama T, Inagaki M,Kawamoto A, et al.Analysis of main bearing force and cylinder block vibration related toengine air borne noise[J].JSAE Review, 2002, 21: 404-406
[320]郝志勇,段秀兵,宋宝安,等.车用柴油机曲轴系统动力学仿真[J].农业机械学报,2005,36(7)：4-7
[321]程金林.基于机体低噪声虚拟设计的曲轴系统耦合动力学研究[D].天津：天津大学,2003
[322]李超,余洋,赵嫚.涡旋压缩机虚拟建模与运动仿真[J].流体机械,2012,40(1)：17-21
[323]张晓君,张波.涡旋压缩机传动系统动平衡研究与优化[J].机械设计与制造,2012,(4)：149-151
[324]戴旭东,王义亮,袁小阳,等.多缸内燃机缸体瞬态动力分析[J].内燃机学报,2003,21(3)：277-282
[325]李俊宝,杨庆佛.柴油机机体振动响应有限分析[J].内燃机工程,1995,16(3)：9-16
[326]Kim,H.J. etal.Balance Weight Design for a Radially Compliant Scroll Compressor. Proc of 1997 Int Compressor Eng Conf at Purdue PP.232-239
[327]彭斌,刘振全.变频涡旋压缩机转子的平衡研究[J].振动工程学报,2004,17(1)：181-183
[328]申永胜.机械原理教程[M].北京：清华大学出版社,2005
[329]刘振全.涡旋式流体机械与涡旋压缩机[M].北京：机械工业出版社,2009
[330]樊林,靳春梅,屈宗长,等.通用型线涡旋压缩机的误差及运动分析[J].机械工报,2002,6(38)：140-143
[331]樊林,耿森林,靳春梅.涡旋压缩机机构统一模型的研究[J].机械科学与技术,2000,5(19)：755-757
[332]时冰.600MW超临界汽轮机再热主汽阀门动力学建模与虚拟样机研究[D].上海：上海交通大学博士论文,2008
[333]阎绍泽,陈鹿民,季林红,等.含间隙较的机械多体系统动力学模型[J].振动工程学报,2003,16(3)：290-294
[334]时冰,金烨.面向虚拟样机的机构间隙旋转铰建模与动力学仿真[J].机械工程学报,2009,45(4)：299-303
[335]白争锋.考虑铰间间隙的机构动力学特性研究[D].哈尔滨工业大学博士论文,2011
[336]Flores P, Ambro J, Claro J C.In:Dynamics analysis for planar multibody mechanical systems with real joints[C].Proceedings of ECCOMAS Thematic Conference on Advances in Computational Mutibody Dynamics. Portugal: Lisbon, 2003:26-41
[337]AMBROSIO J A C.Impact of rigid and flexible multibody systems:Deformation description and contact models[M].Virtual Nonlinear Multibody Systems,Nato Advanced Study Institute, Prague, 2002, 2:15-33