Ca系氧化物冶金工艺对夹杂物及组织的影响

详细信息    查看全文 | 推荐本文 |

英文篇名：The effect of Ca oxide metallurgy on inclusion and metallographic structure 作者：王睿之 ; 杨健 英文作者：WANG Ruizhi;YANG Jian;School of Metallurgy,Northeastern University;Central Research Institute,Baosteel Group Corporation;School of Materials Science and Engineering,Shanghai University; 关键词：焊接热影响区 ; 大线能量焊接 ; 低温韧性 ; 夹杂物 ; 氧化物冶金 英文关键词：heat affected zone;;high heat input welding;;low temperature toughness;;inclusion;;oxide metallurgy 中文刊名：LGZZ 英文刊名：Steelmaking 机构：东北大学冶金学院;宝山钢铁股份有限公司中央研究院;上海大学材料学院; 出版日期：2017-09-25 11:06 出版单位：炼钢 年：2017 期：v.33;No.189 基金：国家重点研发计划项目(2016YFB0300602) 语种：中文; 页：LGZZ201705007 页数：7 CN：05 ISSN：42-1265/TF 分类号：45-51

摘要

基于实验室数据,研究了Ca系氧化物冶金工艺中Ca含量对大线能量焊接热影响区夹杂物和组织的影响。与传统工艺相比,Ca系氧化物冶金工艺微米夹杂物的密度增加,平均尺寸减少,纳米夹杂物密度增加60%,平均尺寸减小25%,热影响区组织由传统工艺的粗大原奥氏体晶粒和魏氏组织为主转变为细小原奥氏体晶粒和晶内针状铁素体为主。随着Ca质量分数从4×10-6增加到27×10-6,微米夹杂物密度增加而尺寸变化不大;纳米夹杂物的密度增加尺寸变小。采用Ca系氧化物冶金工艺的50 mm厚板,大线能量焊接热影响区低温韧性提高到原来的4倍。
        The effect of Ca content on the evolution behavior of inclusions and metallographic structure in the HAZ was investigated based on the experimental studies.Compared the conventional steel,the density of micro-meter inclusions with Ca oxide metallurgy increased and the average size reduced. The density of nano-meter inclusions increased by 60 % and the average size reduced by 25 %. The metallographic structure in HAZ of conventional steel was Widmanstatten structure and Ca oxide metallurgy was intragranular acicular ferrite. As the content of Ca increased from 4 × 10-6to 27 × 10-6,the density of micrometer-inclusions increased and the average size didn't change much and the density of nano-meter inclusions increased,the average size reduced.The low temperature toughness of HAZ of 50 mm thick plate which produced by Ca oxide metallurgy increased at 4 times.

引文

[1]YANG Jian,ZHU Kai,WANG Ruizhi,et al.Technology for improving the toughness of heat affected zones with strong deoxidizers[J].Baosteel Technical Research,2010(4):1-6.
    [2]YANG Jian,XU Longyun,ZHU Kai,et al.Improvement of HAZ toughness of steel plate for high heat input welding by inclusion control with Mg deoxidation[J].Steel Research International,2015,86(6):619-625.
    [3]王睿之,杨健,祝凯,等.钙脱氧和镁脱氧氧化物冶金工艺效果对比[J].炼钢,2016,32(3):50-54.
    [4]DESHIMARU S I,HIRAI I,AMANO K,et al.Production of heavy-gauge steel plates suitable for high-heat input welding in the arctic region[J].Kawasaki Steel Technical Report,1987,17:34-40.
    [5]YANG Jian,ZHU Kai,SHEN Jianguo et al.Improvement of steel cleanliness by deoxidation with Mg vapor[J].Journal of Iron and Steel Research International,2008,15(10):675-680.
    [6]XU Longyu,YANG Jian,WANG Ruizhi,et al.Effect of Mg content on the microstructure and toughness of heat-affected zone of steel plate[J].Metallurgical and Materials Transactions A,2016,47(7):354-3364.
    [7]ZHU Kai,YANG Jian,WANG Ruizhi,et al.Effect of Mg addition on inhibiting austenite grain growth of Ti-bearing low carbon steels[J].Journal of Iron and Steel Research International,2011,18(9):60-64.
    [8]KOJIMA A,UEMORI R,MINAGAWA M,et al.Super high HAZ toughness steels with fine microstructure imparted by fine particles[J].まてりあ:日本金属学会会報,2004,42:67-69.
    [9]MOON J,LEE J,LEE C.Prediction for the austenite grain size in the presence of growing particles in the weld HAZ of Timicroalloyed steel[J].Materials Science&Engineering A,2007,459(1/2):40-46.
    [10]FANG F,YONG Q L,YANG C F,et al.Microstructure and precipitation behavior in HAZ of V and Ti microalloyed steel[J].Journal of Iron and Steel Research,International,2009,16(3):68-72.
    [11]KATO Taku,SATO Shinsuke,OHTA Hiroki,et al.Effects of Ca adition on formation behavior of tin particles and HAZ toughness in large-heat-input welding[J].Kobelco Technology Review,2011(30):76-79.
    [12]TOMITA Y,SAITO N,TSUZUKI T,et al.Improvement in HAZ Toughness of Steel by Ti N-Mn S Addition[J].Transactions of the Iron&Steel Institute of Japan,1994,34(10):829-835.
    [13]吴亦泉,杨健,祝凯,等.含量对船板结构钢中夹杂物的影响[J].宝钢技术,2014(4):1-5.