激光沉积修复ZL114A铝合金的组织及力学性能
|
摘要
采用6 k W光纤激光器对预制槽损伤的ZL114A铸造铝合金进行激光沉积修复实验研究,分析了热处理前后激光修复区的组织形貌及分布规律,并对试样的显微硬度和室温拉伸性能进行了测试。结果表明,修复区与基材形成良好的冶金结合,沉积区底部为近似平行于熔合线法线外延生长的柱状树枝晶,一次枝晶间距约15.7μm,二次枝晶间距约5.2μm,共晶组织呈分叉棒状或块状连续分布于枝晶间隙,在沉积层顶层顶部出现α-Al柱状枝晶转变为等轴枝晶现象。热处理后修复区柱状枝晶的二次枝晶臂因高温原子扩散作用,连成一片,且共晶Si相粒状化明显,粒径约4.93μm,部分颗粒均匀分布于一次枝晶臂的两侧。热处理后修复区硬度较沉积态平均提高约1.6倍,且修复试样的室温拉伸力学性能优于铸造基材。
ZL114A cast aluminum alloy with pre-groove damage was repaired by laser deposition repair(LDR).Microstructure and distribution law of laser deposition repaired zone before and after heat treatment were analyzed,and then microhardness and room temperature tensile properties of the samples were tested.The results show that a good metallurgical combination is formed between the repaired zone and the substrate.At the bottom of the deposition layer,α-Al columnar dendrites,which are approximately parallel to the normal directions of the fusion line appear with epitaxial growth feature.The primary dendrite arm spacing is about 15.7 μm,and the distance between secondary dendrites is about 5.27 μm.Eutectic structure presents as bifurcated rod or block,and continuously distributes in the gaps among dendrite crystals,and α-Al columnar dendrites transforms into equiaxed crystal at the top of the last deposition layer.After the heat treatment,secondary dendrite arm of columnar dendrite is expansive because of atomic diffusion,and eutectic Si granulation is clear,the particle size is about 4.93 μm,and part of them distribute uniformly on both sides of primary dendritic arm.The hardness of repaired area increases by 1.6 times compared with that of the deposited sample after heat treatment,and the room temperature tensile properties are better than those of cast substrates.
ZL114A cast aluminum alloy with pre-groove damage was repaired by laser deposition repair(LDR).Microstructure and distribution law of laser deposition repaired zone before and after heat treatment were analyzed,and then microhardness and room temperature tensile properties of the samples were tested.The results show that a good metallurgical combination is formed between the repaired zone and the substrate.At the bottom of the deposition layer,α-Al columnar dendrites,which are approximately parallel to the normal directions of the fusion line appear with epitaxial growth feature.The primary dendrite arm spacing is about 15.7 μm,and the distance between secondary dendrites is about 5.27 μm.Eutectic structure presents as bifurcated rod or block,and continuously distributes in the gaps among dendrite crystals,and α-Al columnar dendrites transforms into equiaxed crystal at the top of the last deposition layer.After the heat treatment,secondary dendrite arm of columnar dendrite is expansive because of atomic diffusion,and eutectic Si granulation is clear,the particle size is about 4.93 μm,and part of them distribute uniformly on both sides of primary dendritic arm.The hardness of repaired area increases by 1.6 times compared with that of the deposited sample after heat treatment,and the room temperature tensile properties are better than those of cast substrates.
引文
[1]Chen Guozhu(陈国珠),Xia Feng(夏风),Hu Yonggang(胡永刚)et al.Journal of Materials Engineering(材料工程)[J],2011(11):53
[2]Hong He(红鹤),Zhang Xichuan(张希川),An Zhenzhi(安振之)et al.Journal of Shenyang University of Technology(沈阳工业大学学报)[J],2001,23(S):6
[3]Chen Yongxiong(陈永雄),Wei Shicheng(魏世丞),Liang Xiubing(梁秀兵)et al.Journal of Materials Engineering(材料工程)[J],2012(6):16
[4]Wang Xiaoyan(王小艳),Chen Jing(陈静),Lin Xin(林鑫)et al.Chinese Journal of Lasers(中国激光)[J],2009,36(6):1585
[5]Lin Xin(林鑫),Huang Weidong(黄卫东).Scientia Sinica Informationis(中国科学:信息科学)[J],2015,45(9):1111
[6]Wang Huaming(王华明).Acta Aeronautic et Astronautica Sinica(航空学报)[J],2014,35(10):2690
[7]Toyserkani Ehsan,Khajepour Amir,Corbin Stephen.Laser Cladding[M].Netherlands:CRC Press LLC,2005
[8]Durandet Y,Brandt M,Liu Q.Materials Forum[J],2005,29:136
[9]Guo Yongli(郭永利),Liang Gongying(梁工英),Li Lu(李璐).Chinese Journal of Lasers(中国激光)[J],2008,35(2):303
[10]Chen Yongcheng(陈永城),Zhang Shuquan(张述泉),Tian Xiangjun(田象军)et al.Chinese Journal of Lasers(中国激光)[J],2015,42(3):0303008-6
[11]Lu Changliang(卢长亮),Hu Fangyou(胡房友),Huang Xuren(黄旭仁)et al.Ordnance Material Science and Engineering(兵器材料科学与工程)[J],2011,34(6):58
[12]Jiang Hua(姜华),Tang Haibo(汤海波),Fang Yanli(方艳丽)et al.Chinese Journal of Lasers(中国激光)[J],2012,39(2):0203 004
[13]Deng Yuping(邓玉平).Dissertation for Master(硕士论文)[D].Wuhan:Huazhong University of Science&Technology,2008
[14]Fan Yaoqiang(范耀强),Dissertation for Master(硕士论文)[D].Taiyuan:Zhongbei University,2013
[2]Hong He(红鹤),Zhang Xichuan(张希川),An Zhenzhi(安振之)et al.Journal of Shenyang University of Technology(沈阳工业大学学报)[J],2001,23(S):6
[3]Chen Yongxiong(陈永雄),Wei Shicheng(魏世丞),Liang Xiubing(梁秀兵)et al.Journal of Materials Engineering(材料工程)[J],2012(6):16
[4]Wang Xiaoyan(王小艳),Chen Jing(陈静),Lin Xin(林鑫)et al.Chinese Journal of Lasers(中国激光)[J],2009,36(6):1585
[5]Lin Xin(林鑫),Huang Weidong(黄卫东).Scientia Sinica Informationis(中国科学:信息科学)[J],2015,45(9):1111
[6]Wang Huaming(王华明).Acta Aeronautic et Astronautica Sinica(航空学报)[J],2014,35(10):2690
[7]Toyserkani Ehsan,Khajepour Amir,Corbin Stephen.Laser Cladding[M].Netherlands:CRC Press LLC,2005
[8]Durandet Y,Brandt M,Liu Q.Materials Forum[J],2005,29:136
[9]Guo Yongli(郭永利),Liang Gongying(梁工英),Li Lu(李璐).Chinese Journal of Lasers(中国激光)[J],2008,35(2):303
[10]Chen Yongcheng(陈永城),Zhang Shuquan(张述泉),Tian Xiangjun(田象军)et al.Chinese Journal of Lasers(中国激光)[J],2015,42(3):0303008-6
[11]Lu Changliang(卢长亮),Hu Fangyou(胡房友),Huang Xuren(黄旭仁)et al.Ordnance Material Science and Engineering(兵器材料科学与工程)[J],2011,34(6):58
[12]Jiang Hua(姜华),Tang Haibo(汤海波),Fang Yanli(方艳丽)et al.Chinese Journal of Lasers(中国激光)[J],2012,39(2):0203 004
[13]Deng Yuping(邓玉平).Dissertation for Master(硕士论文)[D].Wuhan:Huazhong University of Science&Technology,2008
[14]Fan Yaoqiang(范耀强),Dissertation for Master(硕士论文)[D].Taiyuan:Zhongbei University,2013